Nissan Sentra. Manual — part 299
DLK-312
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
FRONT DOOR
2. Loosen the front door hinge to body bolts. Move the door forward or backward as necessary until within
specifications provided.
3. Tighten the hinge to body bolts to specified torque.
4. Install the front fender. Refer to
DLK-159, "Removal and Installation"
.
SURFACE HEIGHT ADJUSTMENT
1. Loosen the front door hinge nuts (A).
2. Move the top and/or bottom of the door (1) in or out as neces-
sary until it is within specifications provided.
3. Tighten the front door hinge nuts to specified torque.
CAUTION:
• Check front door hinge rotating point for poor lubrication. If necessary, apply a suitable multi-pur-
pose grease.
• After adjusting, apply touch-up paint (body color) to the head of front door hinge bolts and nuts.
• If the clearance measurements cannot be corrected by adjusting the front door assembly, adjust the
following as necessary.
- Front fender: Refer to
.
- Rear door: Refer to
DLK-169, "DOOR ASSEMBLY : Adjustment"
.
DOOR STRIKER ADJUSTMENT
Adjust front door assembly striker so that it becomes parallel with door lock insertion direction.
DOOR HINGE
DOOR HINGE : Removal and Installation
INFOID:0000000009756630
REMOVAL
1. Remove front door assembly (2). Refer to
DLK-309, "DOOR ASSEMBLY : Removal and Installation"
2. Remove bolt (A) and door hinge (1).
Front door hinge bolts
22.0 N·m (2.2 kg-m, 16 ft-lb)
Front door hinge nuts
28.0 N·m (2.9 kg-m, 21 ft-
lb)
ALKIA2705ZZ
FRONT DOOR
DLK-313
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3. Remove door hinge bolts (B) and remove hinge (1).
INSTALLATION
Installation is in the reverse order of removal.
Tighten front door hinge bolts to specified torque.
DLK-164, "DOOR ASSEMBLY : Adjustment"
CAUTION:
• Apply anticorrosive agent onto the front door hinge mating surface.
• After installation, check front door open/close, lock/unlock operation.
• After installation, perform the front door adjustment procedure. Refer to
DOOR CHECK LINK
DOOR CHECK LINK : Removal and Installation
INFOID:0000000009756631
REMOVAL
1. Fully close the front door glass.
2. Remove front door speaker. Refer to
AV-60, "Removal and Installation"
AV-124, "Removal and Installation"
(DIS-
PLAY AUDIO WITHOUT BOSE)
AV-408, "Removal and Installation"
(NAVIGATION WITH BOSE) and
300, "Removal and Installation"
(NAVIGATION WITHOUT BOSE).
3. Remove door check link bolt from body.
4. Remove door check link bolts on door panel.
5. Remove door check link (1) through the hole in door panel (2).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• After installation, check front door open/close, lock/unlock operation.
• Check front door check link rotating point for poor lubrication. If necessary, apply a suitable multi-
purpose grease.
ALKIA2708ZZ
JMKIA8073ZZ
DLK-314
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
FRONT DOOR
: Grease
JMKIA8074ZZ
REAR DOOR
DLK-315
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REAR DOOR
DOOR ASSEMBLY
DOOR ASSEMBLY : Removal and Installation
INFOID:0000000009756632
CAUTION:
• Use two people when removing or installing the rear door assembly due to its heavy weight.
• When removing and installing rear door assembly, support rear door with a suitable tool.
REMOVAL
1. Remove rear door assembly harness grommet (LH) (1) then pull
out door harness from body (2).
2. Disconnect the harness connector (A) from the door harness.
3. Remove the check link bolt from the body.
4. Remove rear door assembly hinge nuts (A) (door side) and the
door assembly (1).
JMKIA8083ZZ
JMKIA8084ZZ
ALKIA2710ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст