Nissan Sentra. Manual — part 229
DLK-32
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
SYSTEM (INTELLIGENT KEY SYSTEM)
*: M/T models do not apply.
WARNING METHOD
The following table shows the alarm or warning methods with chime.
OFF position warning
For internal
When condition A, B or condition C is satisfied
• Condition A
- Ignition switch: ACC position
- Door switch (driver side): ON (Door is open)
• Condition B
- Turn ignition switch from ON to OFF while door is open
• Condition C
- Intelligent Key backside is contacted to push-button ignition switch while
brake pedal is depressed and ignition switch is LOCK or OFF (When the
Intelligent Key battery is discharged)
- Door switch (driver side): ON (Door is open)
For external*
OFF position warning (For internal) is in active mode, driver side door has
been closed.
NOTE:
OFF position (For external) active only when each of the sequence has oc-
curred as below: P position warning
→ ACC warning → OFF position warn-
ing (For internal)
→ OFF position warning (For internal)
P position warning
For internal
• Shift position: Other than P
• Engine is stopped (Ignition switch is turned from ON to OFF)
For external
• P position warning (For internal) operates
• Door switch: ON to OFF (Door is open to close)
• Intelligent Key cannot be detected inside the vehicle
ACC warning
• After P position warning operates, or when ignition switch is turned ON
immediately after P position warning operates
• Ignition switch: ACC
Take away warning
Door status changes
from open to close
• Ignition switch: Other than LOCK and OFF
• Door switch: ON to OFF (Door status changes from open to close)
• Registered Intelligent Key is not detected inside the vehicle
Door status is open
• Ignition switch: Other than LOCK and OFF
• Door switch: ON (Door is open)
• Registered Intelligent Key is not detected inside the vehicle during Key
ID verification for 5 seconds
Push button-ignition
switch operation
• Ignition switch: Other than LOCK position
• Push-button ignition switch is pressed
• Registered Intelligent Key is not detected inside the vehicle
Door lock operation warning
Door lock operation is requested while door lock operation condition of
door request switch is not satisfied
Engine start information
Ignition switch is ON po-
sition
• Ignition switch: ON position
• Shift position: P
• Engine is stopped
Ignition switch is other
than ON position
• Ignition switch: Other than ON
• Shift position: P
• Intelligent Key is in the passenger room after driver door is opened and
closed
Ignition switch is ON po-
sition to OFF position
• Ignition switch: ON position to OFF position
• Shift position: P position
NOTE:
Engine start information turns ON for several seconds and then turns OFF,
when ignition switch is turned to the ON position from the OFF position. En-
gine start information does not turn ON until opening and closing of driver
door is detected again.
Intelligent Key low battery warning
BCM detects that Intelligent Key is low battery, after ignition switch is turned
ON
Key ID warning
• Push-button ignition switch is pressed
• Registered Intelligent Key is not detected inside the vehicle
Warning/Information functions
Operation procedure
SYSTEM (INTELLIGENT KEY SYSTEM)
DLK-33
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
LIST OF OPERATION RELATED PARTS
Parts marked with
× are the parts related to operation.
Warning/Information functions
“KEY” warning
lamp
Shift P
warning
lamp
Warning chime
Engine start
operation in-
dicator lamp
Combination
meter buzzer
Intelligent
Key warn-
ing buzzer
Intelligent Key system malfunction
Indicate
—
—
—
—
OFF position warning
For internal
—
—
Activate
—
—
For external
—
—
—
Activate
—
P position warning
For internal
Blink (yellow)
Indicate
Activate
—
—
For external
—
—
Active
—
ACC warning
—
—
Activate
—
—
Take away warning
Door is open to close
Blink (yellow)
—
Activate
Activate
—
Door is open
—
—
—
—
Push-ignition switch oper-
ation
—
Activate
—
—
Door lock operation warning
—
—
—
Activate
—
Engine start information
—
—
—
—
Indicate
Intelligent Key low battery warning
Blink (green)
—
—
—
—
Key ID warning
Blink (yellow)
—
—
—
—
Function
In
tel
lig
en
t Ke
y
Push
-bu
tton
igni
tio
n
swit
ch
Do
or sw
itch
Do
or re
qu
es
t sw
itch
In
sid
e ke
y an
ten
na
O
ut
sid
e ke
y
a
nt
en
na
In
tel
lig
en
t Ke
y
warn
ing
b
uzze
r
Co
mb
in
at
io
n me
te
r bu
zze
r
CAN co
mm
un
ic
ati
o
n sys
tem
BCM
Shi
ft
P warning l
amp
En
gi
ne
s
tart
op
era
tio
n i
n
di
ca
to
r
la
mp
“KEY” w
a
rni
ng
lamp
Intelligent Key system malfunction
×
×
×
OFF position warning
For internal
×
×
×
×
For external
×
×
×
P position warning
×
×
×
×
×
×
ACC warning
×
×
×
×
Take away warning
Door is open or close
×
×
×
×
×
×
×
×
Door is open
×
×
×
×
×
×
Push-button ignition
switch operation
×
×
×
×
×
×
×
Door lock operation warning
×
×
×
×
×
×
×
Key ID warning
×
×
×
×
×
Engine start information
×
×
×
×
×
×
Intelligent Key low battery warning
×
×
×
×
×
DLK-34
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
SYSTEM (TRUNK LID OPENER SYSTEM)
SYSTEM (TRUNK LID OPENER SYSTEM)
System Diagram
INFOID:0000000009756357
System Description
INFOID:0000000009756358
TRUNK LID OPENER OPERATION
When trunk lid opener switch is ON, BCM operates trunk lid opener actuator.
OPERATION CONDITION
If the following conditions are satisfied, trunk open operation is performed.
AWKIA2189GB
Trunk lid opener switch operation
Operation condition
Trunk lid open
• Trunk lid opener switch is ON
• Vehicle speed is less than 5 km/h (3 MPH)
DIAGNOSIS SYSTEM (BCM)
DLK-35
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)
INFOID:0000000010290941
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions.
Direct Diagnostic Mode
Description
ECU identification
The BCM part number is displayed.
Self Diagnostic Result
The BCM self diagnostic results are displayed.
Data Monitor
The BCM input/output data is displayed in real time.
Active Test
The BCM activates outputs to test components.
Work support
The settings for BCM functions can be changed.
Configuration
• The vehicle specification can be read and saved.
• The vehicle specification can be written when replacing BCM.
CAN DIAG SUPPORT MNTR
The result of transmit/receive diagnosis of CAN communication is displayed.
System
Sub System
Direct Diagnostic Mode
ECU id
en
tif
ica
tion
Se
lf Di
ag
no
st
ic
Res
u
lt
Dat
a
M
on
ito
r
Acti
ve
T
est
W
o
rk
su
pp
ort
Co
nf
ig
ur
at
io
n
CAN DIAG SUP
P
OR
T MNTR
Door lock
DOOR LOCK
×
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp timer
INT LAMP
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps FLASHER
×
×
×
Air conditioner
AIR CONDITIONER
×
Intelligent Key system
INTELLIGENT KEY
×
×
×
×
Combination switch
COMB SW
×
BCM
BCM
×
×
×
×
×
Immobilizer
IMMU
×
×
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Trunk open
TRUNK
×
Vehicle security system
THEFT ALM
×
×
×
RAP system
RETAINED PWR
×
Signal buffer system
SIGNAL BUFFER
×
TPMS
AIR PRESSURE MONITOR
×
×
×
×
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст