Nissan Sentra. Manual — part 883
TM-168
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F11A]
P0706 TRANSMISSION RANGE SENSOR A
NO
>> INSPECTION END
3.
CHECK POWER CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect transmission range switch connector.
3. Turn ignition switch ON.
4. Check voltage between transmission range switch harness connector terminal and ground.
Is the check result normal?
YES
>> GO TO 4.
NO
>> GO TO 7.
4.
CHECK CIRCUIT BETWEEN TRANSMISSION RANGE SWITCH AND TCM (PART 1)
1. Turn ignition switch OFF.
2. Disconnect TCM connector.
3. Check continuity between transmission range switch harness connector terminals and TCM harness con-
nector terminals.
Is the check result normal?
YES
>> GO TO 5.
NO
>> Repair or replace malfunctioning parts.
5.
CHECK CIRCUIT BETWEEN TRANSMISSION RANGE SWITCH AND TCM (PART 2)
Check continuity between transmission range switch harness connector terminals and ground.
Is the check result normal?
YES
>> GO TO 6.
NO
>> Repair or replace malfunctioning parts.
6.
CHECK TRANSMISSION RANGE SWITCH
Check transmission range switch. Refer to
TM-169, "Component Inspection"
Is the check result normal?
YES
>> Check intermittent incident. Refer to
GI-39, "Intermittent Incident"
.
NO
>> Repair or replace malfunctioning parts.
+
-
Voltage
Transmission range switch
Connector
Terminal
F26
4
Ground
10 – 16 V
Transmission range switch
TCM
Continuity
Connector
Terminal
Connector
Terminal
F26
2
F23
4
Existed
5
7
6
2
8
6
9
5
Transmission range switch
—
Continuity
Connector
Terminal
F26
2
Ground
Not existed
5
6
8
9
P0706 TRANSMISSION RANGE SENSOR A
TM-169
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
7.
DETECT MALFUNCTIONING ITEMS
Check the following items:
• Harness open circuit or short circuit between ignition switch and IPDM E/R. Refer to
.
• Harness open circuit or short circuit between IPDM E/R and transmission range switch.
• 10A fuse (No. 45, IPDM E/R). Refer to
PG-49, "IPDM E/R Terminal Arrangement"
.
• IPDM E/R
Is the check result normal?
YES
>> Check intermittent incident. Refer to
GI-39, "Intermittent Incident"
.
NO
>> Repair or replace malfunctioning parts.
Component Inspection
INFOID:0000000009759406
1.
CHECK TRANSMISSION RANGE SWITCH
Check continuity between transmission range switch connector terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> There is a malfunction of transmission range switch. Replace transaxle assembly. Refer to
283, "Removal and Installation"
Transmission range switch
Condition
Continuity
Terminal
7 – 10
Manual lever: “P” and “N” positions
Existed
Other than the above
Not existed
4 – 2
Manual lever: “D” position
Existed
Other than the above
Not existed
4 – 5
Manual lever: “P” position
Existed
Other than the above
Not existed
4 – 6
Manual lever: “L” position
Existed
Other than the above
Not existed
4 – 8
Manual lever: “R” position
Existed
Other than the above
Not existed
4 – 9
Manual lever: “N position
Existed
Other than the above
Not existed
TM-170
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F11A]
P0711 TRANSMISSION FLUID TEMPERATURE SENSOR A
P0711 TRANSMISSION FLUID TEMPERATURE SENSOR A
DTC Logic
INFOID:0000000009759407
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PREPARATION BEFORE WORK
If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.
INSPECTION START
Is it necessary to erase permanent DTC?
YES
>> GO TO 3.
NO
>> GO TO 7.
3.
CHECK DTC (ECM AND TCM)
Check the DTC.
Is any DTC other than “P0711” detected?
YES
>> Check DTC detected item. Refer to
(TCM).
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
Possible causes
P0711
FLUID TEMP SENSOR A
(Transmission Fluid Tempera-
ture Sensor A Circuit Range/
Performance)
When any of 1 or 2 is satisfied:
1.
Under the following diagnosis conditions,
CVT fluid temperature does not rise to
10
°C (50°F) after driving for a certain pe-
riod of time with the TCM-received fluid
temperature sensor value between
−
40
°C (−40°F) and 9°C (48.2°F).
-
Diagnosis condition
•
Selector lever: “D” position
•
Vehicle speed: 10 km/h (7 MPH) or more
•
Engine speed: 450 rpm or more
•
Accelerator pedal position: 1.0/8 or more
•
TCM power supply voltage: More than 11
V
•
CVT fluid temperature: Less than 10
°C
2.
When the condition of the final judgment
is satisfied after satisfying that of the pro-
visional judgment:
-
Provisional judgment: All of the following
conditions are satisfied within 2 seconds
after the ignition switch is turned ON.
•
U0073, U0100, P0712 and P0713 are
not detected.
•
CAN communication is normal.
•
TCM power supply voltage: More than 11
V
•
The difference between CVT fluid tem-
perature and engine coolant temperature
is 37
°C (98.6°F) or more, or −27°C (−
16
°F) or less.
-
Final judgment: When all of the following
conditions are satisfied and this state is
maintained for 300 seconds:
•
ECM is normal.
•
Provisional judgment is satisfied.
CVT fluid temperature sensor
P0711 TRANSMISSION FLUID TEMPERATURE SENSOR A
TM-171
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
NO
>> GO TO 4.
4.
PERFORM DTC CONFIRMATION PROCEDURE (PART 1)
TESTING CONDITION:
• While performing the following procedure, do not add fuel.
• Before performing the following procedure, check that fuel level is between 1/4 and 4/4.
• Before performing the following procedure, confirm that battery voltage is 11 V or more at idle.
With CONSULT
1. Move the vehicle to a cool place.
NOTE:
Cool the vehicle in an environment of ambient air temperature between
−10°C (14°F) and 35°C (95°F).
2. Turn ignition switch OFF and leave the vehicle for 12 hours.
CAUTION:
Never turn ignition switch ON during this procedure.
NOTE:
The vehicle must be cooled with the food open.
3. Turn ignition switch ON.
CAUTION:
Never start the engine.
4. Select “Data Monitor” in “TRANSMISSION”.
5. Select “FLUID TEMP”.
6. Record CVT fluid temperature.
7. Start engine and let it idle for 5 minutes or more.
CAUTION:
Never turn ignition switch OFF during idling.
8. Check 1st trip DTC.
With GST
1. Move the vehicle to a cool place.
NOTE:
Cool the vehicle in an environment of ambient air temperature between
−10°C (14°F) and 35°C (95°F).
2. Turn ignition switch OFF and leave the vehicle for 12 hours.
CAUTION:
Never turn ignition switch ON during this procedure.
NOTE:
The vehicle must be cooled with the food open.
3. Start engine and let it idle for 5 minutes or more.
CAUTION:
Never turn ignition switch OFF during idling.
4. Check 1st trip DTC.
Is “P0711” detected?
YES
>> Go to
NO-1 (With CONSULT)>>GO TO 5.
NO-2 (With GST)>>GO TO 6.
5.
CHECK CVT FLUID TEMPERATURE
With CONSULT
1. Select “Data Monitor” in “TRANSMISSION”.
2. Select “FLUID TEMP”.
Is the value of “FLUID TEMP” 10
°C (50°F) or more?
YES
>> INSPECTION END
NO
>> GO TO 6.
6.
PERFORM DTC CONFIRMATION PROCEDURE (PART 2)
With CONSULT
1. Drive the vehicle for the total minutes specified in the Driving time column below with the following condi-
tions satisfied.
Selector lever
: “D” position
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст