Nissan Sentra. Manual — part 882
TM-164
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F11A]
P0705 TRANSMISSION RANGE SENSOR A
6.
CHECK R POSITION SW CIRCUIT (PART1)
1. Turn ignition switch OFF.
2. Disconnect TCM connector.
3. Check continuity between TCM harness connector terminals.
Is the check result normal?
YES
>> GO TO 7.
NO
>> Repair or replace malfunctioning parts.
7.
CHECK R POSITION SW CIRCUIT (PART 2)
1. Disconnect transmission range switch connector.
2. Turn ignition switch ON.
3. Check voltage between TCM harness connector terminal and ground.
Is the check result normal?
YES
>> GO TO 12.
NO
>> Repair or replace malfunctioning parts.
8.
CHECK P POSITION SW CIRCUIT (PART 1)
1. Turn ignition switch OFF.
2. Disconnect TCM connector.
3. Check continuity between TCM harness connector terminals.
Is the check result normal?
YES
>> GO TO 9.
NO
>> Repair or replace malfunctioning parts.
9.
CHECK P POSITION SW CIRCUIT (PART 2)
1. Disconnect transmission range switch connector.
2. Turn ignition switch ON.
3. Check voltage between TCM harness connector terminal and ground.
TCM
Continuity
Connector
Terminal
F23
6
2
Not existed
4
5
7
+
-
Voltage
(Approx.)
TCM
Connector
Terminal
F23
6
Ground
0 V
TCM
Continuity
Connector
Terminal
F23
7
2
Not existed
4
5
6
P0705 TRANSMISSION RANGE SENSOR A
TM-165
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Is the check result normal?
YES
>> GO TO 12.
NO
>> Repair or replace malfunctioning parts.
10.
CHECK L POSITION SWITCH CIRCUIT (PART 1)
1. Turn ignition switch OFF.
2. Disconnect TCM connector.
3. Check continuity between TCM harness connector terminals.
Is the check result normal?
YES
>> GO TO 11.
NO
>> Repair or replace malfunctioning parts.
11.
CHECK L POSITION SWITCH CIRCUIT (PART 2)
1. Disconnect transmission range switch connector.
2. Turn ignition switch ON.
3. Check voltage between TCM harness connector terminal and ground.
Is the check result normal?
YES
>> GO TO 12.
NO
>> Repair or replace malfunctioning parts.
12.
CHECK TRANSMISSION RANGE SWITCH
Check transmission range switch. Refer to
TM-165, "Component Inspection"
Is the check result normal?
YES
>> Check intermittent incident. Refer to
GI-39, "Intermittent Incident"
.
NO
>> Repair or replace malfunctioning parts.
Component Inspection
INFOID:0000000009759403
1.
CHECK TRANSMISSION RANGE SWITCH
Check continuity between transmission range switch connector terminals.
+
-
Voltage
(Approx.)
TCM
Connector
Terminal
F23
7
Ground
0 V
TCM
Continuity
Connector
Terminal
F23
2
4
Not existed
5
6
7
+
-
Voltage
(Approx.)
TCM
Connector
Terminal
F23
2
Ground
0 V
Transmission range switch
Condition
Continuity
Terminal
7 – 10
Manual lever: “P” and “N” positions
Existed
Other than the above
Not existed
TM-166
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F11A]
P0705 TRANSMISSION RANGE SENSOR A
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> There is a malfunction of transmission range switch. Replace transaxle assembly. Refer to
283, "Removal and Installation"
.
4 – 2
Manual lever: “D” position
Existed
Other than the above
Not existed
4 – 5
Manual lever: “P” position
Existed
Other than the above
Not existed
4 – 6
Manual lever: “L” position
Existed
Other than the above
Not existed
4 – 8
Manual lever: “R” position
Existed
Other than the above
Not existed
4 – 9
Manual lever: “N position
Existed
Other than the above
Not existed
Transmission range switch
Condition
Continuity
Terminal
P0706 TRANSMISSION RANGE SENSOR A
TM-167
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
P0706 TRANSMISSION RANGE SENSOR A
DTC Logic
INFOID:0000000009759404
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PREPARATION BEFORE WORK
If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Maintain the following conditions.
3. Shift the selector lever through entire positions from “P” to “L”. (Hold the selector lever at each position for
35 seconds or more.)
4. Check the first trip DTC.
Is “P0706” detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009759405
1.
ADJUSTMENT OF CONTROL CABLE
Adjust control cable. Refer to
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1. Turn ignition switch ON.
2. Select “Self Diagnostic Results” in “TRANSMISSION”.
3. Touch “Erase”.
4. Perform “DTC CONFIRMATION PROCEDURE”. Refer to
.
Is “P0706” detected?
YES
>> GO TO 3.
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
Possible causes
P0706
T/M RANGE SENSOR A
(Transmission Range Sensor
A Circuit Range/Performance)
All range signals stay OFF continuously for 30
seconds under the following diagnosis condi-
tion 1 and 2:
• Diagnosis condition 1 (continued for 30 sec-
onds or more)
- TCM power supply voltage: More than 11 V
• Diagnosis condition 2 (continued for 2 sec-
onds or more)
- Vehicle speed: Less than 3 km/h (2 MPH)
- Accelerator pedal position: 0.6/8 or less
- Idle switch: ON
- Stop lamp switch: ON
• Harness or connector
(Open circuit between ignition switch
and transmission range switch/open
circuit between transmission range
switch and TCM)
• Transmission range switch
• Control cable
Accelerator pedal position
: 0.0/8
Brake pedal
: Depressed
Vehicle speed
: 0 km/h (0 MPH)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст