Nissan Sentra. Manual — part 930
WT-22
< BASIC INSPECTION >
ID REGISTRATION PROCEDURE
ID REGISTRATION PROCEDURE
Description
INFOID:0000000009758143
This procedure must be performed after replacing wheels, transmitters or the BCM, or rotating wheels.
Work Procedure
INFOID:0000000009758144
TPMS ID registration can be performed using one of the following procedures:
• Transmitter Activation tool (J-45295-A) with CONSULT (preferred method)
• Signal Tech II tool (J-50190) with CONSULT (preferred method)
• Signal Tech II tool (J-50190) without CONSULT
• CONSULT only
TPMS REGISTRATION WITH TRANSMITTER ACTIVATION TOOL (J-45295-A)
With CONSULT
1. Turn the ignition switch ON.
2. Using CONSULT, select “WORK SUPPORT” in BCM (AIR PRESSURE MONITOR). Then, select “ID
REGIST.”
3. Select “Start” on “ID REGIST” screen.
4. Hold the transmitter activation tool (J-45295-A) (1) against the
side of the left front tire, near the valve stem.
5. With the tool held at a 0 to 15 degree angle to the tire, press and
hold the transmitter activation tool button until the indicator lamp
turns OFF (approximately 5 seconds).
6. Repeat steps 4 and 5 for the remaining tires in this order: right
front, right rear and left rear.
7. When ID registration is complete, check the following pattern at each wheel.
8. After the ID registration procedure for all wheels is complete, press “End” on the CONSULT to finish ID
registration.
9. Test drive the vehicle to ensure that the TPMS lamp is OFF and no warning messages are present.
TPMS REGISTRATION WITH SIGNAL TECH II TOOL (J-50190)
NOTE:
The Signal Tech II must be updated with software version 1.1.48 or newer in order to perform the below proce-
dures. The Signal Tech II software updates can only be downloaded from a CONSULT unit with ASIST. Other
versions of ASIST will not show the updates.
With CONSULT
1. Adjust the tire pressure for all tires to the recommended value. Refer to
2. Turn the ignition switch ON.
3. Using CONSULT, select “WORK SUPPORT” in BCM (AIR PRESSURE MONITOR). Then, select “ID
REGIST.”
4. Select “Start” on “ID REGIST” screen.
5. Turn on the Signal Tech II tool (J-50190).
NNEIC0020ZZ
Sequence
ID registration position
Turn signal lamp
CONSULT
1
Front LH
2 blinks
“Yet (red)”
↓
“Done (green)”
2
Front RH
3
Rear RH
4
Rear LH
ID REGISTRATION PROCEDURE
WT-23
< BASIC INSPECTION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
6. Hold the Signal Tech II against the side of the left front tire, near
the valve stem.
7. With the tool held at a 0 to 15 degree angle to the tire, select
“Activate Sensor” from the main menu, then press and release
the “OK” button to activate the sensor. Once the sensor is acti-
vated, the vehicle parking lamps will flash and the sensor ID will
appear on the CONSULT screen.
8. Repeat steps 6 and 7 for the remaining tires in this order: right
front, right rear and left rear.
9. When ID registration is complete, check the following pattern at
each wheel.
10. Once all sensors have been activated, select “End” on the CONSULT to finish ID registration.
11. Test drive the vehicle to ensure that the TPMS lamp is OFF and no warning messages are present.
Without CONSULT
1. Adjust the tire pressure for all tires to the recommended value. Refer to
2. Turn on the Signal Tech II tool (J-50190) and select “TPMS Check” from the main menu.
3. Select vehicle model and year.
4. When prompted, hold the Signal Tech II against the side of the
left front tire, near the valve stem.
5. With the tool held at a 0 to 15 degree angle to the tire, press and
release the “OK” button to activate the sensor. Once the sensor
is activated, the tool will sound a tone and the tire pressure will
be displayed.
6. Repeat steps 4 and 5 for the remaining tires in this order: right
front, right rear and left rear.
7. When prompted, connect the tool to the data link connector. The
tool will connect to the BCM, read the VIN, read sensor IDs and
check for TPMS DTCs. Along with DTCs detected, one of the
following will be displayed next to each wheel:
-
N/A - Not applicable because no ID found by the tool
-
OK - Wheel and sensor are in original position
-
NEW - New ID found compared to BCM
-
RT - Wheel has been rotated
-
Low Press - Low tire pressure
8. If no DTC is present or the repair has been completed, press the “OK” button to register the IDs and clear
DTCs.
9. Test drive the vehicle to ensure that the TPMS lamp is OFF and no warning messages are present.
10. Print a Signal Tech II Audit Report for your records. Refer to the Signal Tech II User Guide for instructions.
TPMS REGISTRATION WITH CONSULT ONLY
With CONSULT
1. Adjust the tire pressure for all wheels to match the list below.
ALEIA0177ZZ
Sequence
ID registration position
Turn signal lamp
CONSULT
1
Front LH
2 blinks
“Yet (red)”
↓
“Done (green)”
2
Front RH
3
Rear RH
4
Rear LH
ALEIA0177ZZ
Tire position
Tire pressure kPa (kg/cm
2
, psi)
Front LH
240 (2.4, 35)
Front RH
220 (2.2, 32)
Rear RH
200 (2.0, 29)
Rear LH
180 (1.8, 26)
WT-24
< BASIC INSPECTION >
ID REGISTRATION PROCEDURE
2. Turn the ignition switch ON.
3. Using CONSULT, select “WORK SUPPORT” in BCM (AIR PRESSURE MONITOR). Then, select “ID
REGIST.”
4. Select “Start” on “ID REGIST” screen.
5. Drive the vehicle at a speed greater than 40 km/h (25 MPH) for 3 minutes or more.
6. After ID registration for all wheels is complete, press “End” on the CONSULT to finish ID registration.
7. Adjust the tire pressures for all tires to the recommended value. Refer to
8. Test drive the vehicle to ensure that the TPMS lamp is OFF and no warning messages are present.
ID registration position
CONSULT
Front LH
“Yet (red)”
↓
“Done (green)”
Front RH
Rear RH
Rear LH
C1704, C1705, C1706, C1707 LOW TIRE PRESSURE
WT-25
< DTC/CIRCUIT DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
DTC/CIRCUIT DIAGNOSIS
C1704, C1705, C1706, C1707 LOW TIRE PRESSURE
DTC Logic
INFOID:0000000009758145
NOTE:
The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II
User Guide for additional information.
• Activate and display TPMS transmitter IDs
• Display tire pressure reported by the TPMS transmitter
• Read TPMS DTCs
• Register TPMS transmitter IDs
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM SELF DIAGNOSTIC RESULT
With CONSULT
1. Turn the ignition switch ON.
2. Check the tire pressure for all wheels and adjust to the specified value. Refer to
.
3. Perform “SELF DIAGNOSTIC RESULT”.
Is DTC “C1704”, “C1705”, “C1706”, or “C1707” detected?
YES
>> Proceed to
.
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000010290194
NOTE:
The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II
User Guide for additional information.
• Activate and display TPMS transmitter IDs
• Display tire pressure reported by the TPMS transmitter
• Read TPMS DTCs
• Register TPMS transmitter IDs
1.
CHECK DATA MONITOR
With CONSULT
1. Drive for 3 minutes at a speed of 40 km/h (25 MPH) or more, then drive normally for 10 minutes.
2. Stop the vehicle.
3. On “DATA MONITOR” select “AIR PRESS FL”, “AIR PRESS FR”, “AIR PRESS RR” and “AIR PRESS
RL”..
4. Within 5 minutes after vehicle stopped, check that the tire pressures are within specification. Refer to
.
DTC
Display item
Malfunction detected condition
Possible causes
C1704
LOW PRESSURE FL
Front LH tire pressure drops to 182.7 kPa (1.9 kg/cm
2
, 26 psi) or less.
Low tire pressure
C1705
LOW PRESSURE FR
Front RH tire pressure drops to 182.7 kPa (1.9 kg/cm
2
, 26 psi) or less.
C1706
LOW PRESSURE RR
Rear RH tire pressure drops to 182.7 kPa (1.9 kg/cm
2
, 26 psi) or less.
C1707
LOW PRESSURE RL
Rear LH tire pressure drops to 182.7 kPa (1.9 kg/cm
2
, 26 psi) or less.
Monitor item
Displayed value
AIR PRESS FL
Approximately equal to value indicated on tire gauge for front LH tire
AIR PRESS FR
Approximately equal to value indicated on tire gauge for front RH tire
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст