Nissan Sentra. Manual — part 908
TM-268
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
PRIMARY SPEED SENSOR
PRIMARY SPEED SENSOR
Exploded View
INFOID:0000000009759519
Removal and Installation
INFOID:0000000009759520
REMOVAL
1. Disconnect the primary speed sensor connector.
2. Remove the primary speed sensor.
3. Remove the O-ring from the primary speed sensor.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse O-ring.
• Apply Genuine NISSAN CVT Fluid NS-3 to the O-ring.
Inspection and Adjustment
INFOID:0000000009759521
INSPECTION AFTER INSTALLATION
Start the engine and check visually that there is no leakage of CVT fluid.
ADJUSTMENT AFTER INSTALLATION
Adjust CVT fluid level. Refer to
Transaxle assembly
O-ring
Primary speed sensor
: Always replace after every disassembly.
: N m (kg-m, in-lb)
: Genuine NISSAN CVT Fluid NS-3
JSDIA1880GB
SECONDARY SPEED SENSOR
TM-269
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
SECONDARY SPEED SENSOR
Exploded View
INFOID:0000000009759522
Removal and Installation
INFOID:0000000009759523
REMOVAL
1. Disconnect the secondary speed sensor connector.
2. Remove the secondary speed sensor.
3. Remove the O-ring from the secondary speed sensor.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse O-ring.
• Apply Genuine NISSAN CVT Fluid NS-3 to the O-ring.
Inspection and Adjustment
INFOID:0000000009759524
INSPECTION AFTER INSTALLATION
Start the engine and check visually that there is no leakage of CVT fluid.
ADJUSTMENT AFTER INSTALLATION
Adjust CVT fluid level. Refer to
Transaxle assembly
O-ring
Secondary speed sensor
: Vehicle front
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: Genuine NISSAN CVT Fluid NS-3
JSDIA1881GB
TM-270
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
OUTPUT SPEED SENSOR
OUTPUT SPEED SENSOR
Exploded View
INFOID:0000000009759525
Removal and Installation
INFOID:0000000009759526
REMOVAL
1. Disconnect the output speed sensor harness connector.
2. Remove the output speed sensor.
3. Remove the O-ring from the output speed sensor.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse O-ring.
• Apply Genuine NISSAN CVT Fluid NS-3 to the O-ring.
Inspection and Adjustment
INFOID:0000000009759527
INSPECTION AFTER INSTALLATION
Start the engine and check visually that there is no leakage of CVT fluid.
ADJUSTMENT AFTER INSTALLATION
Check CVT fluid level. Refer to
Transaxle assembly
Output speed sensor
O-ring
: Vehicle front
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: Genuine NISSAN CVT Fluid NS-3
JSDIA1882GB
DIFFERENTIAL SIDE OIL SEAL
TM-271
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
DIFFERENTIAL SIDE OIL SEAL
Exploded View
INFOID:0000000009759528
Removal and Installation
INFOID:0000000009759529
REMOVAL
NOTE:
Cap or plug openings to prevent fluid from spilling.
1. Remove the front drive shaft (RH/LH). Refer to
FAX-21, "6M/T : Removal and Installation (RH)"
18, "6M/T : Removal and Installation (LH)"
FAX-26, "EXCEPT 6M/T : Removal and Installation"
(Except 6M/T).
2. Use oil seal remover or a similar means and remove the differential side oil seal.
CAUTION:
When removing the differential side oil seal, be careful not to scratch the oil seal mounting sur-
faces of the transaxle case and converter housing.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse differential side oil seal.
• Apply Genuine NISSAN CVT Fluid NS-3 to the differential side oil seal lip and around the oil seal.
• When inserting the drive shaft, be sure to use a protector.
Using Tool, drive the differential side oil seal in until the amount of oil seal projection from the case edge
matches dimensions (C) and (D).
Transaxle assembly
Differential side oil seal (left side)
Differential side oil seal (right side)
: Vehicle front
: Always replace after every disassembly.
: Genuine NISSAN CVT Fluid NS-3
JSDIA1888ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст