Nissan Sentra. Manual — part 909
TM-272
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
DIFFERENTIAL SIDE OIL SEAL
CAUTION:
Be careful not to scratch the lip of the differential side oil seal
when press-fitting it.
NOTE:
The reference is the pull-in direction of the differential side oil seal.
Drift to be used:
Inspection and Adjustment
INFOID:0000000009759530
INSPECTION AFTER INSTALLATION
Drive the vehicle and check visually that there is no leakage of CVT fluid.
ADJUSTMENT AFTER INSTALLATION
Adjust CVT fluid level. Refer to
Tool number
: KV38107900
(A)
: Differential side oil seal (LH)
(B)
: Differential side oil seal (RH)
JSDIA1836ZZ
Dimension “C” :Height difference from case end surface is within 1.8
± 0.5 mm (0.071 ±
0.020 in).
Dimension “D” :Height difference from case end surface is within 1.8
± 0.5 mm (0.071 ±
0.020 in).
Location
Commercial Service Tools
Transaxle case side
Commercial service tool with outer dia. 56 mm (2.20 in) and in-
ner dia. 50 mm (1.97 in)
Converter housing side
WATER HOSE
TM-273
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
WATER HOSE
Exploded View
INFOID:0000000009759531
Removal and Installation
INFOID:0000000009759532
REMOVAL
WARNING:
Do not remove the radiator cap when the engine is hot. Serious burns could occur from high-pressure
coolant escaping from the radiator. Wrap a thick cloth around the cap. Slowly push down and turn it a
quarter turn to allow built-up pressure to escape. Carefully remove the cap by pushing it down and
turning it all the way.
CAUTION:
Perform these steps after the coolant temperature has cooled sufficiently.
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
1. Remove the engine under cover. Refer to
EXT-31, "ENGINE UNDER COVER : Removal and Installation"
.
2. Drain engine coolant from radiator. Refer to
CO-12, "Changing Engine Coolant"
.
3. Remove water hose and heater thermostat assembly.
INSTALLATION
Installation is in the reverse order of removal.
• Refer to the following when installing water hoses.
Water outlet
Heater thermostat assembly
Hose clamp
CVT oil warmer
Water hose
To thermostat housing
To engine oil cooler
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
JSDIA3578GB
TM-274
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
WATER HOSE
• Refer to the followings when installing hose clamp.
CAUTION:
• Do not reuse hose clamp.
• Hose clamp should not interfere with the bulge of fluid cooler tube.
Inspection
INFOID:0000000009759533
INSPECTION AFTER REMOVAL
Heater Thermostat
1. Fully immerse the heater thermostat in a container (A) filled
with water. Continue heating the water while stirring.
2. Continue heating the heater thermostat for 5 minutes or more
after bringing the water to a boil.
3. Quickly take the heater thermostat out of the hot water, measure the heater thermostat within 10 seconds.
Water hose (1)
Installation side tube (2)
Direction of paint mark
Hose insertion depth (L)
Heater thermostat assembly
CVT oil warmer
Frontward
(A): 27 mm (1.06 in) (Hose end reaches
the 2-stage bulge.)
Water hose
CVT oil warmer
Frontward
Water outlet
Frontward
(B): 27 mm (1.06 in) (Hose end reaches
the end of water outlet tube.)
JSDIA3579ZZ
Water hose (1)
Installation side tube (2)
Hose clamp (3)
Direction of tab
Clamping position
Heater thermostat assembly
CVT oil warmer
Frontward
(B): Align with the end of
paint mark (C)
Water hose
CVT oil warmer
Frontward
(A): 5 – 7 mm (0.20 –
0.28 in) (L) from hose
end
Water outlet
Frontward
JSDIA2499ZZ
JSDIA3661ZZ
WATER HOSE
TM-275
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
-
Place dial indicator (A) on the pellet and measure the elonga-
tion from the initial state.
4. If out of standard, replace heater thermostat.
INSPECTION AFTER INSTALLATION
Start the engine, and check the joints for coolant leakage.
Standard
: Refer to
.
JSDIA3662ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст