Nissan Sentra. Manual — part 821
ST-10
< REMOVAL AND INSTALLATION >
STEERING WHEEL
REMOVAL AND INSTALLATION
STEERING WHEEL
Exploded View
INFOID:0000000009759136
Removal and Installation
INFOID:0000000009759137
REMOVAL
NOTE:
When reconnecting spiral cable, fix cable with a tape so that fixing case and rotating part keep aligned. This
will omit neutral position alignment procedure during spiral cable installation.
1. Set steering wheel to the straight-ahead position.
2. Remove driver air bag module. Refer to
SR-12, "Removal and Installation"
.
3. Disconnect harness connectors from clipping locations.
4. Remove steering wheel lock nut.
5. Remove steering wheel using suitable tool (A).
NOTE:
Put paint marks on the steering wheel and the column shaft
head for supporting accurate positioning during the installation
procedure.
INSTALLATION
1.
Driver air bag module
2.
Steering wheel
3.
Steering column assembly
ALGIA0150ZZ
SGIA1524J
STEERING WHEEL
ST-11
< REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
Installation is in the reverse order of removal.
• Check the spiral cable neutral position after replacing or rotating spiral cable. Refer to
.
CAUTION:
• Do not twist spiral cable excessively after it becomes tight. (Twisting may cause the cable to be
torn off.)
• Do not reuse steering wheel lock nut.
ST-12
< REMOVAL AND INSTALLATION >
STEERING COLUMN
STEERING COLUMN
Exploded View
INFOID:0000000009759138
Removal and Installation
INFOID:0000000009759139
REMOVAL
CAUTION:
• While removing the steering column assembly, do not unlock the tilt lever.
• Do not impact on the axis when removing steering column assembly.
• Be careful when removing steering column assembly from the vehicle because it is heavy.
• Keep steering column assembly away from magnetic sources.
• Do not disassemble steering column assembly, it is all one piece.
• While removing the steering column assembly, do not move the steering gear assembly.
• When removing the steering column assembly, be careful not to allow the lower shaft assembly to
turn.
1. Set steering wheel to the straight-ahead position.
2. Place the tilt to the lowest level.
CAUTION:
Securely lock the tilt lever.
3. Remove instrument lower panel LH. Refer to
IP-21, "Removal and Installation"
.
4. Remove driver air bag module. Refer to
SR-12, "Removal and Installation"
.
5. Remove steering wheel. Refer to
ST-10, "Removal and Installation"
.
6. Remove steering column cover. Refer to
IP-16, "Removal and Installation"
7. Remove spiral cable. Refer to
SR-16, "Removal and Installation"
.
8. Remove combination switch.
9. Disconnect key interlock cable (if equipped). Refer to
TM-260, "Removal and Installation"
.
1.
Steering column assembly
2.
Slide plates
3.
lower shaft assembly
ALGIA0151ZZ
STEERING COLUMN
ST-13
< REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
10. Remove hole cover (1).
• Lower shaft assembly (2).
11. Remove lower side bolt of lower shaft assembly.
12. Disconnect each harness connector and harness clips installed to steering column assembly.
13. Disconnect EPS control unit harness connectors.
14. Remove the steering column assembly nuts.
CAUTION:
When removing the steering column assembly nuts, be careful not to drop the steering column
assembly.
15. Remove the steering column.
16. Remove EPS control unit. Refer to
STC-39, "Removal and Installation"
INSTALLATION
CAUTION:
• Do not impact on the axis when removing steering column assembly.
• When installing the steering column cover, check that the vehicle harness is not stuck in the cover.
Installation is in the reverse order of removal.
• After tightening nut (A) of the steering column assembly, press in
slide plate (outer and inner) (1) to tighten nut (B).
CAUTION:
• Do not reuse slide plate.
• The slide plate must be securely pressed in before tighten-
ing the nut of slide plate.
• Lower shaft bolt is directional. Refer to
.
CAUTION:
Do not reuse lower shaft assembly bolt.
• After installing steering column assembly, perform self-diagnosis with CONSULT to ensure correct opera-
• Perform inspection after installation. Refer to
.
ALGIA0157ZZ
JPGIA0118ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст