Nissan Sentra. Manual — part 822
ST-14
< REMOVAL AND INSTALLATION >
STEERING GEAR AND LINKAGE
STEERING GEAR AND LINKAGE
Exploded View
INFOID:0000000009759140
REMOVAL
Removal and Installation
INFOID:0000000009759141
REMOVAL
1. Set steering wheel to the straight-ahead position.
2. Remove floor cover (1).
• Lower shaft assembly (2).
3. Remove the lower shaft assembly bolt and position the lower shaft assembly out of the way. Refer to
12, "Removal and Installation"
.
CAUTION:
• Spiral cable may be cut if steering wheel turns while separating steering column assembly and
steering gear assembly. Always fix the steering wheel using string to avoid turning.
• Place a matching mark on both intermediate shaft and steering gear assembly before removing
intermediate shaft.
4. Remove wheels and tires using power tool. Refer to
1.
Steering gear assembly
2.
Front suspension member
Front
AWGIA0254ZZ
ALGIA0157ZZ
STEERING GEAR AND LINKAGE
ST-15
< REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
5. Remove steering outer socket from steering knuckle so as not to
damage ball joint boot using Tool.
CAUTION:
Temporarily tighten the nut to prevent damage to threads
and to prevent the Tool from a sudden drop.
6. Remove front suspension member. Refer to
7. Remove steering gear assembly from front suspension member.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Spiral cable may be cut if steering wheel turns while separating steering column assembly and steer-
ing gear assembly. Always fix the steering wheel using string to avoid turning.
• Perform final tightening of nuts and bolts on each part under unladen conditions with tires on level ground
when removing steering gear assembly.
• Check wheel alignment. Refer to
• Rotate steering wheel to check for decentered condition, binding, noise or excessive steering effort.
• Do not reuse steering outer socket nut and steering gear assembly nut.
• Perform neutral position steering angle adjustment. Refer to
Tool number : HT72520000 (J-25730-A)
AWGIA0252ZZ
ST-16
< UNIT DISASSEMBLY AND ASSEMBLY >
STEERING GEAR AND LINKAGE
UNIT DISASSEMBLY AND ASSEMBLY
STEERING GEAR AND LINKAGE
Exploded View
INFOID:0000000009759142
Disassembly and Assembly
INFOID:0000000009759143
DISASSEMBLY
1. Loosen outer socket lock nut, and remove outer socket.
CAUTION:
When loosening lock nut, be sure to fix outer socket with a wrench or an equivalent.
2. Remove boot clamps, and then remove boot from inner socket.
CAUTION:
• Do not damage inner socket part and gear housing part of steering gear assembly when remov-
ing boot. steering gear assembly must be replaced if steering gear assembly are damaged
because it may cause foreign material interfusion.
• Do not reuse boot clamps.
3. Remove inner socket.
ASSEMBLY
1.
Outer socket
2.
Boot clamp (small diameter)
3.
Boot
4.
Boot clamp (large diameter)
5.
Inner socket
6.
Gear housing assembly
AWGIA0317ZZ
STEERING GEAR AND LINKAGE
ST-17
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
1. Apply recommended grease to inner socket (A) of gear housing
assembly, and install boot to gear housing assembly.
Use Genuine Lithium Soap, Autorex A (manufactured by
Kyodo yushi) or equivalent.
CAUTION:
Do not reuse boot.
2. Install boot clamp (large diameter) (1) to boot using Tool.
CAUTION:
• Do not reuse boot clamp (large diameter).
• Install boot clamp (large diameter) securely to boot
groove, and crimp it so as to have clearance (B) of 3 mm
(0.12 in) or less as shown.
3. Install boot clamp (small diameter) to boot.
CAUTION:
Do not reuse boot clamp (small diameter).
4. Adjust inner socket to standard length (L), and then tighten outer
socket lock nut (1) to the specified torque. Check length again
after tightening lock nut.
CAUTION:
• When tightening the outer socket lock nut (1), be sure to
fix outer socket (2) with suitable tool to prevent the ball
joint from getting contact with the knuckle.
• Adjust toe-in after this procedure. The length achieved
after toe-in adjustment is not necessary the above value.
Grease application position (Reference)
(B)
: 10 mm (0.39 in)
JPGIA0102ZZ
Tool number (A)
: KV40107300 ( — )
JSGIA0140ZZ
(L)
: Refer to
JPGIA0187ZZ
JSGIA0538ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст