Nissan Sentra. Manual — part 206
CLUTCH FLUID
CL-9
< PERIODIC MAINTENANCE >
C
E
F
G
H
I
J
K
L
M
A
B
CL
N
O
P
7. Return clutch tube and lock pin in their original positions while clutch pedal is depressed.
8. Perform the air bleeding. Refer to
.
Air Bleeding
INFOID:0000000009757024
CAUTION:
• Monitor clutch fluid level in reservoir tank so as not to empty the tank.
• Do not spill clutch fluid onto painted surfaces. If fluid spills, wipe up immediately and wash the
affected area with water.
1. Fill reservoir tank with new clutch fluid.
CAUTION:
Do not reuse drained clutch fluid.
2. Connect a transparent vinyl hose to air bleeder of bleeding con-
nector (1).
3. Depress and release the clutch pedal slowly and fully 15 times
at an interval of 2 to 3 seconds and release the clutch pedal.
4. Press the lock pin (1) into the bleeding connector (2), and main-
tain the position.
5. Slide bleeding connector (1) in the direction of the arrow ( ) as
shown and immediately depress the clutch pedal and hold it, to
bleed the air from the system.
CAUTION:
Clutch tube is under hydraulic pressure; do not allow the
clutch tube to disconnect from the clutch housing.
6. Return clutch tube and lock pin in their original positions.
7. Release clutch pedal and wait for 5 seconds.
8. Repeat steps 3 to 7 until no bubbles are observed in the clutch fluid.
9. Check that the fluid level in the reservoir tank is within the specified range after air bleeding. Refer to
.
JPDIB0166ZZ
JPDIB0041ZZ
(2)
: Clutch housing
Dimension (A)
: 10 mm (0.39 in)
JPDIB0042ZZ
CL-10
< REMOVAL AND INSTALLATION >
CLUTCH PEDAL
REMOVAL AND INSTALLATION
CLUTCH PEDAL
Exploded View
INFOID:0000000009757025
Removal and Installation
INFOID:0000000009757026
REMOVAL
1. Remove instrument lower panel LH. Refer to
IP-21, "Removal and Installation"
.
2. Disconnect the harness connector from the clutch pedal position switch (if equipped).
3. Disconnect the harness connector from the clutch interlock switch (if equipped).
4. Disconnect clip of harness from clutch pedal.
5. Remove clutch master cylinder rod end from clutch pedal.
6. Remove clutch pedal position switch and clip from clutch pedal
(if equipped).
7. Remove clutch interlock switch and clip from clutch pedal (if
equipped).
8. Remove clutch pedal from the vehicle.
9. Remove pedal pad from clutch pedal.
10. Remove stopper rubber and pedal stopper rubber from clutch
pedal, using a suitable remover.
INSTALLATION
Installation is in the reverse order of removal.
1.
Clutch pedal
2.
Stopper rubber
3.
Clip
4.
Clutch interlock switch (if equipped) 5.
Clutch pedal position switch (if equipped) 6.
Pedal pad
7.
Pedal stopper rubber
JSDIA3615GB
PCIB1491E
CLUTCH PEDAL
CL-11
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
CL
N
O
P
CAUTION:
After applying recommended grease, press clutch master cylinder rod end into clutch pedal until it
stops.
Inspection and Adjustment
INFOID:0000000009757027
INSPECTION AFTER REMOVAL
• Check clutch pedal for bend, damage, or a cracked weld. If bend, damage, or a cracked weld is found,
replace clutch pedal.
• Check pedal stopper rubber (if equipped). If damage or deformation is found, replace pedal stopper rubber.
(if equipped)
• Check stopper rubber. If damage or deformation is found, replace stopper rubber.
• Check pedal pad. If wear or damage is found, replace pedal pad.
INSPECTION AFTER INSTALLATION
• Check the height of clutch pedal. Refer to
CL-5, "Inspection and Adjustment"
.
• Check the clutch interlock switch position (if equipped). Refer to
CL-5, "Inspection and Adjustment"
• Check the clutch pedal position switch position (if equipped). Refer to
CL-5, "Inspection and Adjustment"
.
ADJUSTMENT AFTER INSTALLATION
• Adjust the clutch interlock switch position (if equipped). Refer to
CL-5, "Inspection and Adjustment"
• Adjust the clutch pedal position switch position (if equipped). Refer to
CL-5, "Inspection and Adjustment"
.
CL-12
< REMOVAL AND INSTALLATION >
CLUTCH MASTER CYLINDER
CLUTCH MASTER CYLINDER
Exploded View
INFOID:0000000009757028
Removal and Installation
INFOID:0000000009757029
REMOVAL
CAUTION:
• Keep painted surface on the body or other parts free of clutch fluid. If it spills, wipe up immediately
and wash the affected area with water.
• Do not disassemble clutch master cylinder.
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
1. Drain clutch fluid. Refer to
.
2. Remove air cleaner body assembly. Refer to
EM-25, "Removal and Installation"
3. Remove reservoir hose from reservoir tank and clutch master cylinder.
4. Remove clutch master cylinder rod end (
) from clutch pedal.
1.
Reservoir hose
2.
Reservoir tank
3.
Clutch master cylinder
ALDIA0405ZZ
PCIB1491E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст