Nissan Sentra. Manual — part 305
DLK-336
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
TRUNK LID
Installation is in the reverse order of removal.
CAUTION:
After installation, perform the trunk lid assembly adjustment procedure. Refer to
.
FUEL FILLER LID OPENER
DLK-337
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
FUEL FILLER LID OPENER
Exploded View
INFOID:0000000009756654
FUEL FILLER LID
FUEL FILLER LID : Removal and Installation
INFOID:0000000009756655
REMOVAL
1. Fully open fuel filler lid.
2. Remove fuel cap clip (A).
1.
Fuel filler lid
2.
Bumper rubber
3.
Fuel filler lid opener cable
4.
Fuel filler lid lock
A.
Clip
B.
Bolts
C.
Cable protector
ALKIA2919ZZ
ALKIA2921ZZ
DLK-338
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
FUEL FILLER LID OPENER
3. Remove fuel filler lid screws (A) and fuel filler lid (1).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, check fuel filler lid assembly open/close, lock/unlock operation.
NOTE:
• The following table shows the specifications for a correctly installed fuel filler lid.
• Fitting adjustment cannot be performed.
Unit: mm (in)
FUEL FILLER OPENER CABLE
FUEL FILLER OPENER CABLE : Removal and Installation
INFOID:0000000009756656
REMOVAL
1. Remove hood and fuel filler handle assembly bolts (A).
2. Release fuel filler lid opener cable (2) by pulling downward and
then sliding cable end to the side to remove from hood and fuel
filler handle assembly (1).
3. Remove dash side finisher (LH). Refer to
INT-26, "DASH SIDE FINISHER : Removal and Installation"
4. Remove center pillar lower finisher (LH). Refer to
INT-27, "CENTER PILLAR LOWER FINISHER :
.
ALKIA2929ZZ
Portion
Measurement
Standard
Fuel filler lid – Body side outer
Clearance
5.1
±1.0 (0.20 ±0.04)
Fuel filler lid – Body side outer
Surface height
0.0
±1.0 (0.0 ±0.04)
JMKIA7998ZZ
JMKIA7999ZZ
FUEL FILLER LID OPENER
DLK-339
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
5. Remove rear seat bolster (LH). Refer to
SE-24, "Removal and Installation - Rear Seat Bolster"
.
6. Remove trunk side finisher (LH). Refer to
INT-43, "TRUNK SIDE FINISHER : Removal and Installation"
.
7. Remove fuel filler lid opener cable (1) from fuel filler lid lock assembly. Refer to
OPENER CABLE : Removal and Installation"
.
8. Remove each cable protector (A), then remove fuel filler lid opener cable (1).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, check fuel filler lid assembly open/close, lock/unlock operation.
FUEL FILLER LID LOCK
FUEL FILLER LID LOCK : Removal and Installation
INFOID:0000000009756657
REMOVAL
1. Fully open fuel filler lid.
Front
ALKIA2931ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст