Nissan GT-R. Manual — part 110
REAR COMBINATION LAMP
EXL-57
< REMOVAL AND INSTALLATION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Install in the reverse order of removal.
Replacement
INFOID:0000000009160393
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
REAR TURN SIGNAL LAMP BULB
1.
Remove the trunk lid finisher. Refer to
INT-29, "Removal and Installation"
2.
Remove the rubber cover (1).
3.
Turn the rear turn signal lamp bulb socket (2) counterclockwise
and unlock it.
4.
Remove the bulb (3) from the rear turn signal lamp bulb socket.
BACK-UP LAMP BULB
1.
Remove the trunk lid finisher. Refer to
INT-29, "Removal and Installation"
2.
Remove the rubber cover (1).
3.
Turn the back-up lamp bulb socket (2) counterclockwise and
unlock it.
4.
Remove the bulb (3) from the back-up lamp bulb socket.
NNLIA0016ZZ
NNLIA0015ZZ
EXL-58
< REMOVAL AND INSTALLATION >
[XENON TYPE]
REAR SIDE MARKER LAMP
REAR SIDE MARKER LAMP
Exploded View
INFOID:0000000009160394
Removal and Installation
INFOID:0000000009160395
REMOVAL
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
1.
Remove the rear bumper fascia. Refer to
2.
Disconnect the rear side marker lamp connector.
3.
Remove the rear side marker lamp mounting bolts and clip.
4.
Remove the rear side marker lamp.
INSTALLATION
Install in the reverse order of removal.
1.
Rear side marker lamp
JPLIA1160ZZ
HIGH-MOUNTED STOP LAMP
EXL-59
< REMOVAL AND INSTALLATION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
HIGH-MOUNTED STOP LAMP
Exploded View
INFOID:0000000009160396
Removal and Installation
INFOID:0000000009160397
REMOVAL
CAUTION:
Disconnect the battery negative terminal or the remove the fuse.
1.
Remove the rear wing. Refer to
.
2.
Remove the center leg bracket.
3.
Remove the high-mounted stop lamp mounting screw. And then
cut the two-sided tape by the any appropriate tool (A).
4.
Disconnect the connector. And then remove the high-mounted
stop lamp from the rear wing.
INSTALLATION
Install in the reverse order of removal.
1.
Rear wing
2.
High-mounted stop lamp
3.
Center leg bracket
NNLIA0017ZZ
NNLIA0018ZZ
EXL-60
< REMOVAL AND INSTALLATION >
[XENON TYPE]
LICENSE PLATE LAMP
LICENSE PLATE LAMP
Exploded View
INFOID:0000000009160398
Removal and Installation
INFOID:0000000009160399
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
REMOVAL
1.
Remove the license plate lamp in numerical order shown in the
figure.
2.
Disconnect the connector.
3.
Remove license plate lamp.
INSTALLATION
1.
Connect the connector.
2.
Fix the pawl side. And then push the resin clip side.
Replacement
INFOID:0000000009160400
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
LICENSE PLATE LAMP BULB
1.
Remove license plate lamp. Refer to
.
1.
License plate lamp
NNLIA0026ZZ
JPLIA0056ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст