Nissan GT-R. Manual — part 108
FRONT COMBINATION LAMP
EXL-49
< REMOVAL AND INSTALLATION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
4.
Headlamp is turn ON for about 30 minutes, check that there are not on and off light, abnormality such as
blinking whether brightness of right and left does not have a difference.
EXL-50
< REMOVAL AND INSTALLATION >
[XENON TYPE]
DAYTIME RUNNING LIGHT
DAYTIME RUNNING LIGHT
Exploded View
INFOID:0000000009160384
Removal and Installation
INFOID:0000000009160385
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
REMOVAL
Left side
1.
EXT-36, "ENGINE UNDER COVER : Removal and Installation"
2.
Remove washer tank mounting bolt, and then keep a service area.
3.
Disconnect daytime running light harness connector.
4.
Remove daytime running light mounting bolt and nut, and then remove daytime running light bracket.
5.
Move daytime running light (1) until it contacts bumper fascia rib
portion (A).
1.
Bumper fascia
2.
Daytime running light
3.
U nut
4.
Daytime running light bracket A
5.
Daytime running light bracket B
JMLIA1867ZZ
JMLIA1918ZZ
DAYTIME RUNNING LIGHT
EXL-51
< REMOVAL AND INSTALLATION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
6.
Rotate daytime running light around center of rib portion and
remove LED hyper day light.
Right side
1.
Remove bumper fascia. Refer to
EXT-15, "Removal and Installation"
.
2.
Remove daytime running light mounting bolt and nut, and then remove daytime running light bracket.
3.
Move daytime running light (1) until it contacts bumper fascia rib
portion (A).
4.
Rotate daytime running light around center of rib portion and
remove LED hyper day light.
INSTALLATION
Install in the reverse order of removal.
JMLIA1919ZZ
JMLIA1918ZZ
JMLIA1919ZZ
EXL-52
< REMOVAL AND INSTALLATION >
[XENON TYPE]
FRONT SIDE MARKER LAMP
FRONT SIDE MARKER LAMP
Exploded View
INFOID:0000000009160386
Removal and Installation
INFOID:0000000009160387
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
REMOVAL
1.
Insert any appropriate tool (A) into the gap between the side turn
signal lamp and fender protector.
2.
Pull the side turn signal lamp toward vehicle outside while push-
ing metal clip (B) toward vehicle front, and then remove side turn
signal lamp from vehicle.
3.
Disconnect the side turn signal lamp connector.Remove the side turn signal lamp.
NOTE:
Support the vehicle-side harness of the side turn signal lamp with tape so that it does not drop inside the front
fender.
INSTALLATION
1.
Connect the side turn signal lamp connector.
2.
Fix the pawl side. And then push the clip side.
Replacement
INFOID:0000000009160388
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
FRONT SIDE MARKER LAMP BULB
1.
Front side marker lamp
JPLIA1330ZZ
: Vehicle front
NNLIB0018ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст