Nissan GT-R. Manual — part 107
FRONT COMBINATION LAMP
EXL-45
< REMOVAL AND INSTALLATION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
REMOVAL AND INSTALLATION
FRONT COMBINATION LAMP
Exploded View
INFOID:0000000009160379
REMOVAL
DISASSEMBLY
Removal and Installation
INFOID:0000000009160380
REMOVAL
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
1.
Front combination lamp
NNLIA0006ZZ
1.
Front turn signal lamp bulb
2.
Front turn signal lamp bulb socket
3.
Resin cap
4.
Seal packing
5.
Xenon bulb socket
6.
Xenon bulb (LO)
7.
Retaining spring
8.
Resin cap
9.
Seal packing
10.
Halogen bulb (HI)
11. Seal packing
12. HID control unit
13.
Parking lamp bulb
14. Parking lamp bulb socket
15. Rubber seal
16.
Headlamp housing assembly
Refer to
for symbols in the figure.
NNLIB0022ZZ
EXL-46
< REMOVAL AND INSTALLATION >
[XENON TYPE]
FRONT COMBINATION LAMP
1.
Remove front bumper fascia. Refer to
2.
Remove the headlamp mounting bolts.
3.
Remove the harness clip (A) and the washer tube (B)*.
*: Left side only
4.
Pull out the headlamp assembly forward the vehicle.
5.
Disconnect the connector before removing the headlamp hous-
ing assembly.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• After installation, perform aiming adjustment. Refer to
• After installation, check that headlamp lighting. Refer to
EXL-48, "Inspection After Installation (HID
.
• When the front combination lamp on one side is replaced, and rubber seal is not installed to the front
combination lamp on the side that is not replaced, install a rubber seal to the front combination lamp
that is not replaced as per the following procedure.
• Always clean the front combination lamp surface where rubber seal is affixed.
1.
Align rubber seal (1) with lens inner protrusion (A) and affix so that there is not gap.
2.
Align rubber seal edge (1) with hood seal assembly edge (2) and affix under hood seal assembly.
JPLIA1163ZZ
NNLIB0019ZZ
FRONT COMBINATION LAMP
EXL-47
< REMOVAL AND INSTALLATION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
3.
Align rubber seal end (1) with hood end (3) and affix so that it does not protrude from hood.
Replacement
INFOID:0000000009160381
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
• After installing the bulb, install the resin cap and the bulb socket securely for watertightness.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, ,moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
HEADLAMP BULB (LO)
1.
Remove the front tire. Refer to
.
2.
Remove the fender protector. Keep a service area. Refer to
EXT-29, "FENDER PROTECTOR : Exploded
.
3.
Rotate the resin cap counterclockwise and unlock it.
4.
Rotate the bulb socket counterclockwise and unlock it.
5.
Remove the retaining spring lock. Remove the bulb from the headlamp housing assembly.
CAUTION:
Never break the xenon bulb ceramic tube when replacing the bulb.
HEADLAMP BULB (HI)
1.
Remove the front tire. Refer to
.
2.
Remove the fender protector. Keep a service area. Refer to
EXT-29, "FENDER PROTECTOR : Exploded
.
3.
Remove the washer tank inlet. Refer to
*: When replace a left.
4.
Rotate the resin cap counterclockwise and unlock it.
5.
Disconnect the headlamp bulb (HI) connector.
NNLIB0020ZZ
EXL-48
< REMOVAL AND INSTALLATION >
[XENON TYPE]
FRONT COMBINATION LAMP
6.
Rotate the bulb socket counterclockwise and unlock it.
7.
Remove the bulb from the headlamp housing assembly.
PARKING LAMP BULB
1.
Rotate the bulb socket counterclockwise and unlock it.
2.
Remove the bulb from the bulb socket.
FRONT TURN SIGNAL LAMP BULB
1.
Remove the front tire. Refer to
.
2.
Remove the fender protector. Keep a service area. Refer to
EXT-29, "FENDER PROTECTOR : Exploded
.
3.
Rotate the bulb socket counterclockwise and unlock it.
4.
Remove the bulb from the bulb socket.
Disassembly and Assembly
INFOID:0000000009160382
DISASSEMBLY
1.
Rotate the resin cap counterclockwise and unlock it.
2.
Rotate the xenon bulb socket counterclockwise and unlock it.
3.
Remove the retaining spring lock. And then remove the xenon bulb.
4.
Remove the HID control unit installation screw.
5.
Remove the HID control unit harness installation screw. And then disconnect the connector from
HID control unit.
6.
Pull out the xenon bulb socket from the headlamp housing assembly.
7.
Rotate the resin cap counterclockwise and unlock it.
8.
Disconnect the headlamp (HI) connector.
9.
Rotate the halogen bulb socket counterclockwise and unlock it.
10. Remove the halogen bulb socket from the headlamp housing assembly.
11. Rotate the parking lamp bulb socket counterclockwise and unlock it.
12. Remove the bulb from the parking lamp bulb socket.
13. Rotate the front turn signal lamp bulb socket counterclockwise and unlock it.
14. Remove the bulb from the front turn signal lamp bulb socket.
ASSEMBLY
Assemble in the reverse order of disassembly.
CAUTION:
• Install HID control unit securely.
• After installing the bulb, install the resin cap and the bulb socket securely for watertightness.
• Seal packing cannot be reused.
• After installation, check that headlamp lighting. Refer to
EXL-48, "Inspection After Installation (HID
.
Inspection After Installation (HID Control Unit)
INFOID:0000000009160383
CAUTION:
Temporarily install the headlamp on the vehicle. Connect the battery to the connector (vehicle side)
when checking ON/OFF status.
XENON HEADLAMP LIGHTING CHECK
When recycled HID control unit, check the following, when there is abnormality replace the HID control unit.
1.
Xenon bulb is cold condition (turn OFF more than 10 minutes), and repetition does headlamp turned ON/
OFF, check that a headlamp illuminated it surely.
2.
Headlamp is turn ON until the xenon bulb becomes stable condition (for about 5 minutes) from cold condi-
tion, check that there are not on and off light, abnormality such as blinking.
3.
Xenon bulb is warm condition (turn ON more than 15 minutes and turn OFF for 1 minute), and repetition
does headlamp turned ON/OFF, check that a headlamp illuminated it surely.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст