Nissan GT-R. Manual — part 180
INT-22
< REMOVAL AND INSTALLATION >
FLOOR TRIM
FLOOR TRIM
Exploded View
INFOID:0000000009162335
Removal and Installation
INFOID:0000000009162336
REMOVAL
1.
Remove the front seat assembly (LH/RH). Refer to
SE-49, "Removal and Installation"
.
2.
Remove rear seat cushion. Refer to
SE-56, "Removal and Installation"
.
3.
Remove the footrest.
1.
Seal box cover
2.
Floor carpet hook
3.
Footrest
4.
Foot duct
5.
Floor carpet fixing clip
6.
Floor carpet
7.
Grille
8.
Front floor spacer (RH)
9.
Front floor spacer (LH)
10. Rear floor spacer (LH)
11.
Rear floor spacer (RH)
: Pawl
: Vehicle front
JMJIA2170ZZ
FLOOR TRIM
INT-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
4.
Disengage and remove the clips of floor carpet hook (1) using
the remover tool (A).
5.
Remove the floor side anchor bolt of front seat belt (LH/RH). Refer to
.
6.
Remove the center console assembly. Refer to
IP-23, "Removal and Installation"
7.
Remove the side instrument panel (LH/RH). Refer to
IP-13, "Removal and Installation"
8.
Remove the foot duct (LH/RH) (1) and floor harness fixing clamp (B) using the remover tool (A).
9.
Disconnect the center connector of diagnosis sensor unit. Refer to
SR-25, "Removal and Installation"
.
10. Remove the dash side finisher (LH/RH), kicking plate inner (LH/RH), and body side welt (LH/RH). Refer to
INT-15, "Removal and Installation"
11. Remove the front side of rear side finisher to obtain the space between rear side finisher and floor carpet.
12. Disengage the floor carpet fixing clip and then remove the tool box cover and the amplifier cover.
INSTALLATION
Install in the reverse order of removal.
: Clip
JMJIA0092GB
NNJIA0024ZZ
INT-24
< REMOVAL AND INSTALLATION >
HEADLINING
HEADLINING
Exploded View
INFOID:0000000009162337
Removal and Installation
INFOID:0000000009162338
REMOVAL
1.
Remove the body side welt (LH/RH) and the front pillar garnish (LH/RH). Refer to
.
2.
Disconnect the inside mirror harness connector. Refer to
MIR-15, "Removal and Installation"
.
1.
Headlining clip
2.
Headlining
3.
Sun-visor assembly RH
4.
Sun-visor cover RH
5.
Sun-visor holder
6.
Sun-visor assembly LH
7.
Sun-visor cover LH
8.
Roof harness
9.
Dual-lock fastener
10. Roof bracket
11. Roof plate
12. Map lamp lens
13. Map lamp lens
: Pawl
: Metal clip
: Vehicle front
JMJIA5350ZZ
HEADLINING
INT-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
3.
Disengage the clips (B) and then, disconnect the connector (A)
of roof harness of front pillar LH.
4.
Remove the sun-visor assembly (LH/RH).
• Remove the sun-visor cover (LH/RH).
• Remove the mounting screw (B) of sun-visor (1) (LH/RH)
using screwdriver (A).
• Disconnect the vanity mirror lamp harness connector.
5.
Rotate the sun-visor holder (1) 90 degrees counterclockwise,
pull it downward, and then remove.
6.
Remove the kicking plate inner (LH/RH), rear seat cushion back (LH/RH), rear side finisher (LH/RH), rear
pillar finisher (LH/RH), and rear body side welt (LH/RH). Refer to
INT-15, "Removal and Installation"
7.
Remove the passenger side front seat. Refer to
SE-49, "Removal and Installation"
.
8.
Remove the A/T shift selector. Refer to
TM-16, "Removal and Installation"
9.
Remove the center console assembly. Refer to
IP-23, "Removal and Installation"
10. Remove the rear hidden clips from the roof panel at the rear end of the headlining, using a remover tool.
11. Disengage the joint of dual-lock fastener (A) and metal clip (B) of
roof console assembly.
12. Check that the dual-lock fastener on the front end of the headlin-
ing is removed. If it is not removed, use a remover tool to
remove it.
CAUTION:
• Roof console assembly is crimped from the back of head-
lining. Remove it by disengaging the crimped area from
back of roof console assembly after removing headlining
from the vehicle.
• Never wrinkle the headlining by bending during work.
JMJIA2168ZZ
JMJIA2169ZZ
NNJIA0027ZZ
: Metal clip
JMJIA1008ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст