Nissan Cube. Manual — part 230
DLK-186
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
RADIATOR CORE SUPPORT
RADIATOR CORE SUPPORT
Exploded View
INFOID:0000000009950605
Removal and Installation
INFOID:0000000009950606
RADIATOR CORE SUPPORT UPPER
REMOVAL
1.
Remove front bumper fascia and bumper reinforcement. Refer to
EXT-12, "Removal and Installation"
2.
Remove hood lock. Refer to
DLK-210, "Removal and Installation"
3.
Remove front combination lamps (LH/RH). Refer to
EXL-191, "Removal and Installation"
.
4.
Remove air guide.
5.
Remove horn. Refer to
HRN-6, "Removal and Installation"
6.
Remove crash zone sensor. Refer to
SR-22, "Removal and Installation"
.
7.
Remove ambient sensor. Refer to
HAC-123, "Removal and Installation"
.
8.
Disconnect all harness from radiator core support upper.
9.
Remove air duct assembly. Refer to
EM-24, "Removal and Installation"
10. Remove radiator core support upper bracket (LH/RH).
11. Remove mounting bolts, and then remove radiator core support upper.
INSTALLATION
1.
Radiator core support side
2.
Radiator core support upper bracket
(LH)
3.
Radiator core support upper bracket
(RH)
4.
Radiator core reinforcement side
5.
Air guide
6.
Radiator core lower stay
7.
Radiator core support lower
8.
Radiator core support upper
JMKIA3625ZZ
RADIATOR CORE SUPPORT
DLK-187
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Install in the reverse order of removal.
CAUTION:
• After installation, adjust the following parts.
- Front combination lamp: Refer to
EXL-187, "Aiming Adjustment Procedure"
RADIATOR CORE SUPPORT LOWER
REMOVAL
1.
Remove front bumper fascia and bumper reinforcement. Refer to
EXT-12, "Removal and Installation"
2.
Remove air guide.
3.
Remove radiator core lower stay.
4.
Remove clips of fender protector.
5.
Remove floor under cover. Refer to
EXT-22, "Removal and Installation"
6.
Use a belts (A) to suspend it to prevent it from falling.
CAUTION:
Never damage radiator and condenser.
7.
Remove mounting bolts, and then remove radiator core support lower.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• After installation, adjust the following parts.
- Front combination lamp: Refer to
EXL-187, "Aiming Adjustment Procedure"
JMKIA3809ZZ
DLK-188
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
FRONT FENDER
FRONT FENDER
Exploded View
INFOID:0000000009950607
Removal and Installation
INFOID:0000000009950608
CAUTION:
Use a shop cloth to protect the body from being damaged during removal and installation.
REMOVAL
1.
Remove side turn signal lamp. Refer to
EXL-198, "Removal and Installation"
.
2.
Remove front grille. Refer to
EXT-17, "Removal and Installation"
3.
Remove front bumper fascia. Refer to
EXT-12, "Removal and Installation"
.
4.
Remove front combination lamp. Refer to
EXL-191, "Removal and Installation"
5.
Remove clips and screws of fender protector. Refer to
EXT-21, "FENDER PROTECTOR : Removal and
.
6.
Remove front fender cover.
7.
Remove mounting bolts and remove front fender.
CAUTION:
An viscous urethane foam is installed on the back surface of front fender. When removing the
front fender, be careful to not deform the front fender while performing the procedure and remov-
ing the viscous urethane foam a little at a time.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
1.
Front fender cover
2.
Front fender assembly
3.
Doube-faced adhesive tape [t : 2.0
mm (0.079 in)]
: Pawl
Refer to
for symbols in the figure.
JMKIA3626ZZ
FRONT FENDER
DLK-189
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
• After installation, apply the touch-up paint (the body color) onto the head of front fender mounting
bolts.
• After installation, adjust the following part.
- Hood assembly : Refer to
DLK-182, "HOOD ASSEMBLY : Adjustment"
.
- Front door : Refer to
DLK-191, "DOOR ASSEMBLY : Adjustment"
- Front combination lamp : Refer to
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст