Nissan Cube. Manual — part 229
DLK-182
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
HOOD
• After installing, perform hood fitting adjustment. Refer to
DLK-182, "HOOD ASSEMBLY : Adjust-
HOOD ASSEMBLY : Adjustment
INFOID:0000000009950600
Check the clearance and the surface height between hood and each part by visually and touching.
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
Unit: mm (in)
1.
Hood assembly
2.
Hood bumper rubber
3.
Hood hinge
4.
Hood lock assembly
5.
Front grille
6.
Front combination lamp
7.
Front fender
Refer to
for symbols in the figure.
Portion
Standard
Difference
(RH/LH)
Hood – Front grille
A – A D
Clearance
6.0 – 10.0 (0.236 – 0.394)
< 2.0 (0.079)
Hood – Front combination lamp B – B E
Clearance
6.0 – 10.0 (0.236 – 0.394)
< 2.0 (0.079)
Hood – Front fender
C – C
F
Clearance
2.5 – 4.5 (0.098 – 0.177)
< 1.0 (0.039)
G Surface height - 1.0 – 1.0 (- 0.039 – 0.039)
—
JMKIA3826GB
HOOD
DLK-183
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
1.
Remove hood lock and adjust the surface height of hood, front grill and front fender according to the fitting
standard dimension, by rotating hood bumper rubber (body side).
2.
Loosen hood hinge mounting nuts on the hood.
3.
Check that hood lock primary latch is securely engaged with striker by dropping hood from approximately
200 mm (7.874 in) height or by pressing lightly on the hood.
CAUTION:
Never drop hood from a height of 300 mm (11.811 in) or more
4.
Install as static closing face of hood is 94– 490 N (9.6 – 50.0 kg, 21.1 – 110 lb).
5.
After adjustment tighten lock bolts to the specified torque.
CAUTION:
• Check hood hinge rotating part for poor lubrication. If necessary, apply body grease.
• After installation, apply touch-up paint (the body color) onto the heads of hood hinge mounting bolts
and nuts.
HOOD HINGE
HOOD HINGE : Exploded View
INFOID:0000000009950601
HOOD HINGE : Removal and Installation
INFOID:0000000009950602
REMOVAL
1.
Remove hood assembly. Refer to
DLK-181, "HOOD ASSEMBLY : Removal and Installation"
2.
Remove front fender. Refer to
DLK-188, "Removal and Installation"
1.
Hood assembly
2.
Hood bumper rubber (hood side)
3.
Radiator core seal
4.
Clamp
5.
Hood bumper rubber (body side)
6.
Hood hinge
7.
Hood support rod
8.
Grommet
: Clip
: Pawl
Refer to
JMKIA3624ZZ
DLK-184
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
HOOD
3.
Remove cowl top. Refer to
EXT-19, "Removal and Installation"
4.
Remove hood hinge mounting bolts, and then remove hood hinge.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check hood hinge rotating part for poor lubrication. If necessary, apply grease.
• After installation, apply touch-up paint (the body color) onto the head of the hinge mounting bolts
and nuts.
• After installation, perform hood fitting adjustment. Refer to
DLK-182, "HOOD ASSEMBLY : Adjust-
HOOD SUPPORT ROD
HOOD SUPPORT ROD : Exploded View
INFOID:0000000009950603
HOOD SUPPORT ROD : Removal and Installation
INFOID:0000000009950604
REMOVAL
1.
Support hood assembly with a suitable material to prevent it from falling.
WARNING:
Bodily injury may occur if no supporting rod is holding the hood open when removing the hood
support rod.
2.
Pull hood support rod from grommet and remove.
1.
Hood assembly
2.
Hood bumper rubber (hood side)
3.
Radiator core seal
4.
Clamp
5.
Hood bumper rubber (body side)
6.
Hood hinge
7.
Hood support rod
8.
Grommet
: Clip
: Pawl
Refer to
for symbols in the figure.
JMKIA3624ZZ
HOOD
DLK-185
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INSTALLATION
Install in the reverse order of removal.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст