Nissan Cube. Manual — part 504
FSU-10
< REMOVAL AND INSTALLATION >
FRONT COIL SPRING AND STRUT
• Become it in ID letter (A) an illustration to the body front side.
• Perform final tightening of bolts and nuts, under unladen conditions
with tires on level ground.
Disassembly and Assembly
INFOID:0000000009948823
DISASSEMBLY
CAUTION:
Never damage strut assembly piston rod when removing components from strut assembly.
1.
Install strut attachment (A) [SST: ST35652000 (
—
)] to strut
assembly and secure it in a vise.
CAUTION:
When installing the strut attachment to strut assembly,
wrap a shop cloth around strut to protect from damage.
2.
Using a spring compressor (A) (commercial service tool), com-
press coil spring between strut mounting bearing and lower seat
(strut assembly) until coil spring with a spring compressor is
free.
CAUTION:
Be sure a spring compressor is securely attached to coil
spring. Compress coil spring.
3.
Check coil spring with a spring compressor between strut
mounting bearing and lower seat (strut assembly) is free. And
then remove piston rod lock nut while securing the piston rod tip
so that piston rod does not turn.
4.
Remove strut mounting insulator and strut mounting bearing,
and bound bumper from strut.
5.
After removing coil spring with a spring compressor (commercial service tool), then gradually release a
spring compressor.
CAUTION:
Loosen while making sure coil spring attachment position does not move.
6.
Remove the strut attachment [SST: ST35652000 (
—
)] from strut.
ASSEMBLY
1.
Install strut attachment [SST: ST35652000 (
—
)] to strut and secure it in a vise.
CAUTION:
When installing the strut attachment to strut assembly, wrap a shop cloth around strut to protect
from damage.
2.
Install bound bumper onto strut mounting insulator.
3.
Compress coil spring using a spring compressor (commercial service tool), and install it onto strut assem-
bly.
CAUTION:
: Vehicle front
JPEIA0023JP
JPEIA0006ZZ
JPEIA0168ZZ
FRONT COIL SPRING AND STRUT
FSU-11
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
• Face tube side of coil spring (1) downward. Align the
lower end (A) to lower seat (strut assembly) (2).
• Be sure a compressor is securely attached to coil spring.
Compress coil spring.
4.
Install strut mounting bearing and strut mounting insulator with bound bumper to strut.
• Installation position of strut mounting insulator is shown in the
figure.
5.
Secure piston rod tip so that piston rod does not turn, then
tighten piston rod lock nut with specified torque.
CAUTION:
Never reuse piston rod lock nut.
6.
Gradually release a spring compressor (commercial service
tool), and remove coil spring.
CAUTION:
Loosen while making sure coil spring attachment position does not move.
7.
Remove the strut attachment [SST: ST35652000 (
—
)] from strut assembly.
Inspection
INFOID:0000000009948824
INSPECTION AFTER DISASSEMBLY
Strut
Check the following items, and replace the parts if necessary.
• Strut for deformation, cracks or damage.
• Piston rod for damage, uneven wear or distortion.
• Oil leakage.
Strut Mounting Insulator and bound bumper Inspection
Check strut mounting insulator and bound bumper for cracks, wear or damage. Replace it if necessary.
Coil Spring
Check coil spring for cracks, wear or damage. Replace it if necessary.
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connector. Refer to
BRC-110, "FRONT WHEEL SENSOR :
.
2.
Check wheel alignment. Refer to
3.
Adjust neutral position of steering angle sensor. Refer to
BRC-9, "Special Repair Requirement"
Disposal
INFOID:0000000009948825
1.
Set strut assembly horizontally to the ground with the piston rod fully extracted.
JPEIA0095ZZ
: Vehicle front
JPEIA0023JP
FSU-12
< REMOVAL AND INSTALLATION >
FRONT COIL SPRING AND STRUT
2.
Drill 2 – 3 mm (0.08 – 0.12 in) hole at the position (
) from top
as shown in the figure to release gas gradually.
CAUTION:
• Wear eye protection (safety glasses).
• Wear gloves.
• Be careful with metal chips or oil blown out by the com-
pressed gas.
NOTE:
• Drill vertically in this direction (
).
• Directly to the outer tube avoiding brackets.
• The gas is clear, colorless, odorless, and harmless.
3.
Position the drilled hole downward and drain oil by moving the piston rod several times.
CAUTION:
Dispose of drained oil according to the law and local regulations.
A
: 20 – 30 mm (0.79 – 1.18 in)
JPEIA0160ZZ
TRANSVERSE LINK
FSU-13
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
TRANSVERSE LINK
Exploded View
INFOID:0000000009948826
Removal and Installation
INFOID:0000000009948827
REMOVAL
1.
Remove tires with power tool. Refer to
.
2.
Remove under cover. Refer to
3.
Remove transverse link from steering knuckle. Refer to
4.
Remove transverse link from suspension member.
NOTE:
Support the point around from upper link (right side) with a jack when removing transverse link (right side).
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform final tightening of bolts and nuts at the front suspension member, under unladen conditions with
tires on level ground.
Inspection
INFOID:0000000009948828
INSPECTION AFTER REMOVAL
Transverse Link
Check the following items, and replace the part it necessary.
• Transverse link and bushing for deformation, cracks or damage.
• Ball joint boot for cracks or other damage, and also for grease leakage.
Swing Torque
1.
Manually move ball stud to confirm it moves smoothly with no binding.
2.
Move ball stud at least ten times by hand to check for smooth movement.
1.
Upper link (right side)
2.
Front suspension member
3.
Transverse link
Refer to
JPEIA0179GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст