Nissan Cube. Manual — part 505
FSU-14
< REMOVAL AND INSTALLATION >
TRANSVERSE LINK
3.
Hook a spring balance (A) at cutout on ball stud (B). Confirm
spring balance measurement value is within specifications when
ball stud begins moving.
-
If swing torque exceeds standard range, replace transverse link
assembly.
Axial End Play
1.
Move ball stud at least ten times by hand to check for smooth movement.
2.
Move tip of ball stud in axial direction to check for looseness.
-
If axial end play exceeds the standard value, replace transverse link assembly.
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connector. Refer to
BRC-110, "FRONT WHEEL SENSOR :
.
2.
Check wheel alignment. Refer to
.
3.
Adjust neutral position of steering angle sensor. Refer to
BRC-9, "Special Repair Requirement"
Swing torque
: Refer to
.
Measurement on
spring balance
: Refer to
.
JPEIA0138ZZ
Axial end play
: Refer to
FRONT STABILIZER
FSU-15
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
FRONT STABILIZER
Exploded View
INFOID:0000000009948829
Removal and Installation
INFOID:0000000009948830
REMOVAL
1.
Remove tires power tool. Refer to
2.
Remove front suspension member. Refer to
3.
Remove stabilizer connecting rod.
4.
Remove mounting bolts (
) of stabilizer clamp, and then
remove stabilizer clamp and stabilizer bushing from front sus-
pension member.
5.
Remove stabilizer bar.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Install stabilizer clamp that a linear hole (A) becomes vehicle front
side (
).
• Install stabilizer bushing that slit (B) becomes vehicle rear side.
1.
Stabilizer bar
2.
Stabilizer clamp
3.
Stabilizer bushing
4.
Stabilizer connecting rod
5.
Front suspension member
Refer to
JPEIA0180GB
WEIA0182E
JPEIA0188ZZ
FSU-16
< REMOVAL AND INSTALLATION >
FRONT STABILIZER
• Tighten the mounting nut to the specified torque while holding a hexagonal part of stabilizer connecting rod
side.
• Perform final tightening of bolts and nuts at the vehicle installation position (rubber bushing), under unladen
conditions with tires on level ground.
Inspection
INFOID:0000000009948831
INSPECTION AFTER REMOVAL
Check stabilizer bar, stabilizer connecting rod, stabilizer bushing and stabilizer clamp for deformation, cracks
or damage. Replace it if necessary.
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connector. Refer to
BRC-110, "FRONT WHEEL SENSOR :
.
2.
Check wheel alignment. Refer to
.
3.
Adjust neutral position of steering angle sensor. Refer to
FRONT SUSPENSION MEMBER
FSU-17
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
FRONT SUSPENSION MEMBER
Exploded View
INFOID:0000000009948832
Removal and Installation
INFOID:0000000009948833
REMOVAL
1.
Remove tires with power tool. Refer to
.
2.
Remove under cover. Refer to
3.
Remove wheel sensor. Refer to
BRC-110, "FRONT WHEEL SENSOR : Exploded View"
.
4.
Remove stabilizer connecting rod from strut assembly. Refer to
.
5.
Remove rear torque rod. Refer to
.
6.
Remove transverse link from steering knuckle. Refer to
7.
Remove steering outer socket from steering knuckle. Refer to
.
8.
Remove intermediate shaft from steering gear assembly. Refer to
9.
Set suitable jack under front suspension member.
CAUTION:
Check the stable condition when using a jack.
10. Remove member stay rear mounting bolts.
11. Remove upper link mounting bolts (right side: vehicle body side, left side: suspension member side), and
suspension member mounting bolts.
12. Gradually lower the jack to remove front suspension member from vehicle body.
CAUTION:
Check the stable condition when using a jack.
13. Remove upper link (left side) from vehicle body.
14. Remove upper link (right side), transverse links, stabilizer assembly from suspension member.
15. Remove steering gear assembly from suspension member. Refer to
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform final tightening of bolts and nuts, under unladen conditions with tires on level ground.
1.
Upper link (right side)
2.
Front suspension member
3.
Upper link (left side)
4.
Member stay
Refer to
JPEIA0181GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст