Nissan Cube. Manual — part 919
ST-18
< REMOVAL AND INSTALLATION >
STEERING GEAR AND LINKAGE
17. Install boot clamp (large diameter) (1) to boot using boot band
crimping tool [SST: KV40107300 (
—
)].
CAUTION:
• Never reuse boot clamp (large diameter).
• Install boot clamp (large diameter) (1) securely to boot
groove, and crimp it so as to have clearance of 3 mm (0.12
in) or less as shown.
18. Install boot clamp (small diameter) to boot.
CAUTION:
Never reuse boot clamp (small diameter).
19. Install joint cover (1) to gear housing assembly (2).
CAUTION:
Install joint cover so that the protrusion for locating is
securely set to gear housing groove.
20. Adjust inner socket to standard length (L), and then tighten lock
nut (1) to the specified torque. Check length again after tighten-
ing lock nut.
CAUTION:
• When tightening lock nut, be sure to fix outer socket with
a wrench or equivalent to prevent ball joint from getting
contact with knuckle.
• Adjust toe-in after this procedure. The length achieved
after toe-in adjustment is not necessary the above value.
Inspection
INFOID:0000000009949823
INSPECTION AFTER INSTALLATION
• Check if steering wheel turns smoothly when it is turned several times fully to the end of the left and right.
• Check the steering wheel play, neutral position steering wheel, steering wheel turning force, and front wheel
turning angle. Refer to
.
INSPECTION AFTER DISASSEMBLY
Boot
• Check boot for cracks, and replace it if a malfunction is detected.
Gear Housing Assembly
• Check gear housing assembly for damage and scratches (inner wall). Replace if there are any abnormal
conditions.
Outer Socket and Inner Socket
• Check the following items and replace the component if it does not meet the standard.
BALL JOINT SWINGING TORQUE
SGIA1302E
SGIA1303E
Inner socket length (L)
: Refer to
.
JPGIA0187ZZ
STEERING GEAR AND LINKAGE
ST-19
< REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
• Hook a spring balance at the point shown in the figure and pull the
spring balance. Make sure that the spring balance reads the spec-
ified value when ball stud and inner socket start to move. Replace
outer socket and inner socket if they are outside the standard.
BALL JOINT AXIAL END PLAY
• Apply an axial load of 490 N (50 kg, 110 lb) to ball stud. Using a
dial gauge, measure amount of stud movement, and then make
sure that the value is within the following specified range. Replace
outer socket (1) and inner socket (2) if the measured value is out-
side the standard.
(Measuring point of outer socket: Ball stud upper
side)
Outer socket
: Refer to
Swing Force and Rotating
Torque"
.
(Measuring point of inner socket: “*” mark shown in
the figure)
Inner socket
: Refer to
Swing Force and Rotating
Torque"
.
Outer socket
: Refer to
Inner socket
: Refer to
SGIA0896E
JSGIA0109ZZ
ST-20
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General Specifications
INFOID:0000000009949824
Steering Wheel Axial End Play and Play
INFOID:0000000009949825
Unit: mm (in)
Steering Wheel Turning Force
INFOID:0000000009949826
Unit: N (kg-f, lb-f)
Steering Angle
INFOID:0000000009949827
Unit: Degree minute (Decimal degree)
Steering Column Operating Range
INFOID:0000000009949828
Rack Stroke
INFOID:0000000009949829
Unit: mm (in)
Socket Swing Force and Rotating Torque
INFOID:0000000009949830
Steering gear model
R24K
Item
Standard
Steering wheel axial end play
0 (0)
Steering wheel play on the outer circumference
0 - 35 (0 - 1.38)
Item
Standard
Steering wheel turning force
36 (3.7, 8.09) or less
Item
Standard
Wheel size: 15 inch
Wheel size: 16 inch
Inner wheel
Minimum
35
°
00
′
(35.0
°
)
Nominal
38
°
00
′
(38.0
°
)
Maximum
39
°
00
′
(39.0
°
)
Outer wheel
Nominal
33
°
00
′
(33.0
°
)
Tilt operating range
40 mm (1.57 in)
Rotating torque
0 – 2.1 N·m (0 – 0.21 kg-m, 0 – 2 in-lb)
Steering column length
458.1 – 462.1 mm (18.04 – 18.19 in)
Item
Standard
Rack stroke neutral position
65.0 (2.56)
Item
Spring balance
Outer socket
Swinging torque
0.3 – 2.9 N·m (0.03 – 0.30 kg-m, 3 – 26 in-lb)
Spring balance measurement
6.0 – 58 N (0.61 – 5.9 kg-f, 1.35 – 13.03 lb-f)
Inner socket
Swinging torque
0.5 – 5.0 N·m (0.05 – 0.51 kg-m, 4 – 44 in-lb)
Spring balance measurement
4.3 – 43.5 N (0.44 – 4.4 kg-f, 0.97 – 9.77 lb-f)
SERVICE DATA AND SPECIFICATIONS (SDS)
ST-21
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
Socket Axial End Play
INFOID:0000000009949831
Inner Socket Length
INFOID:0000000009949832
Unit: mm (in)
Item
Standard
Outer socket
0.5 mm (0.020 in) or less
Inner socket
0.2 mm (0.008 in) or less
Item
Standard
Inner socket length
57.8 (2.276)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст