Nissan Cube. Manual — part 941
TM-20
< REMOVAL AND INSTALLATION >
[6MT: RS6F94R]
CONTROL LINKAGE
8.
Remove clips from the air duct and air cleaner case.
TM-22, "Removal and Installation"
.
9.
Remove air cleaner case and air ducts. Refer to
EM-24, "Removal and Installation"
.
10. Pull out and disconnect the each cable from the shifter lever A and the selector lever, using a suitable
remover.
11. Remove each lock plate upward to disconnect the each cable from the cable mounting bracket.
12. Remove cable mounting bracket from the transaxle case.
13. Remove center muffler, exhaust front tube, and heat plate. Refer to
EX-5, "Removal and Installation"
14. Remove bracket from the vehicle.
15. Release the tabs (A) on the front and back of the M/T shift selec-
tor (1) to remove the M/T shift selector from under the vehicle.
INSTALLATION
Note the following, and install in the reverse order of removal.
• To install the shifter lever knob, press it into the shifter lever.
CAUTION:
• Never reuse shifter lever knob.
• Be careful with orientation of shifter lever knob.
• Shift the shifter lever in the neutral position.
• Tapping work for tapping bolts is not applied to new transaxle case. Do not perform tapping by other than
screwing tapping bolts because tapping is formed by screwing tapping bolts into transaxle case.
CAUTION:
Never reuse tapping bolt.
• Shift the shifter lever A in the neutral position.
• Insert the each cable until it reaches the shifter lever A and the selector lever.
• The lock plate (1) which fixes the selector cable (2) has an indenta-
tion (
). Never confuse the lock plate with the lock plate (3) which
fixes the shifter cable (4).
• Insert the each lock plate until it reaches the cable mounting
bracket.
Install the selector cable according to the following instructions.
1.
Install the selector cable (1) on the cable mounting bracket to
install the lock plate.
2.
Install the selector cable on the selector lever (2).
3.
Slide the stopper (3) in the direction of the arrow (A) shown in
the figure.
4.
Press the lock (4) in the direction of the arrow (B) shown in the
figure.
CAUTION:
Never move the selector lever.
5.
Side the stopper in the direction of the arrow (C) shown in the
figure.
CAUTION:
Never move the selector lever.
: Vehicle front
JPDIC0658ZZ
: Vehicle front
JPDIC0659ZZ
JPDIC0709ZZ
CONTROL LINKAGE
TM-21
< REMOVAL AND INSTALLATION >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Inspection
INFOID:0000000009948873
INSPECTION AFTER INSTALLATION
• Check that the shifter lever knob maintains its position.
• Operate the shifter lever in each position to check that the shifter lever smoothly operates without any com-
plication, snag, noise, backlash, or interference. If any malfunction is fund, repair malfunctioning parts or
replace the M/T shift selector.
• Check that the shifter lever automatically and smoothly returns to the neutral position when selecting the 1st-
2nd side and the 5th-6th side. If any malfunction is fund, repair malfunctioning parts or replace the M/T shift
selector.
TM-22
< REMOVAL AND INSTALLATION >
[6MT: RS6F94R]
AIR BREATHER HOSE
AIR BREATHER HOSE
Exploded View
INFOID:0000000009948874
Removal and Installation
INFOID:0000000009948875
REMOVAL
1.
Remove air duct (inlet). Refer to
EM-24, "Removal and Installation"
2.
Remove clip from the air duct.
3.
Remove air duct. Refer to
EM-24, "Removal and Installation"
.
4.
Remove clip from the air cleaner case.
5.
Remove air breather hose from the 2 way connector.
CAUTION:
When removing air breather hose, be sure to hold 2 way connector securely.
INSTALLATION
Note the following, and install in the reverse order of removal.
• When installing air breather hose on 2 way connector, aim paint mark face toward the vehicle front.
• When installing air breather hose on 2 way connector, push it until it hits transaxle case.
• When installing air breather hose to air cleaner case, make sure that clip are fully inserted.
CAUTION:
Make sure that air breather hose is not collapsed or blocked due to folding or bending when
installed.
1.
Air cleaner case
2.
Air breather hose
3.
Air duct
4.
Clip
5.
Transaxle assembly
6.
2 way connector
SCIA7629E
POSITION SWITCH
TM-23
< REMOVAL AND INSTALLATION >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
POSITION SWITCH
Exploded View
INFOID:0000000009948876
Removal and Installation
INFOID:0000000009948877
REMOVAL
1.
Filler plug
2.
Gasket
3.
Transaxle case
4.
Bushing
5.
Snap ring
6.
Oil channel
7.
Oil gutter
8.
Position switch
9.
Bracket
10. Differential side oil seal
11. Magnet
12. Drain plug
13. Input shaft oil seal
14. Clutch housing
15. 2 way connector
16. Plug
17. Pinion shaft
18. Pinion gear
: Apply Genuine Silicone RTV or an equivalent. Refer to
GI-22, "Recommended Chemical Products and Sealants"
.
Refer to
for symbols not described on the above.
JPDIC0437GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст