Nissan Cube. Manual — part 940
TM-16
< PREPARATION >
[6MT: RS6F94R]
PREPARATION
Drift
a: 45 mm (1.77 in) dia.
b: 39 mm (1.54 in) dia.
Installing differential side bearing inner race
(clutch housing side)
Drift
a: 52 mm (2.05 in) dia.
b: 45 mm (1.77 in) dia.
Installing differential side bearing inner race
(transaxle case side)
Puller
• Removing differential side bearing inner
race (clutch housing side)
• Removing differential side bearing inner
race (transaxle case side)
Puller
• Removing differential side bearing inner
race (clutch housing side)
• Removing differential side bearing inner
race (transaxle case side)
• Removing input shaft rear bearing
• Removing input shaft front bearing
• Removing mainshaft rear bearing inner race
• Removing 6th main gear
• Removing 4th main gear
• Removing 5th main gear
• Removing 1st main gear
• Removing 1st-2nd synchronizer hub as-
sembly
• Removing 2nd main gear
• Removing 3rd main gear
• Removing mainshaft front bearing inner
race
Remover
• Removing bushing
• Removing mainshaft rear bearing outer
race
Power tool
Loosening bolts and nuts
Tool name
Description
S-NT474
S-NT474
NT077
ZZB0823D
S-NT134
PBIC0190E
GEAR OIL
TM-17
< PERIODIC MAINTENANCE >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
PERIODIC MAINTENANCE
GEAR OIL
Inspection
INFOID:0000000009948866
OIL LEAKAGE
Make sure that gear oil is not leaking from transaxle or around it.
OIL LEVEL
1.
Remove filler plug (1) and gasket from transaxle case.
2.
Check the oil level from filler plug mounting hole as shown in the
figure.
CAUTION:
Never start engine while checking oil level.
3.
Set a gasket on filler plug and then install it to transaxle case.
CAUTION:
Never reuse gasket.
4.
Tighten filler plug to the specified torque. Refer to
Draining
INFOID:0000000009948867
1.
Start engine and let it run to warm up transaxle.
2.
Stop engine. Remove drain plug (1) and gasket, using a socket
[Commercial service tool] and then drain gear oil.
3.
Set a gasket on drain plug and install it to clutch housing, using
a socket [Commercial service tool].
CAUTION:
Never reuse gasket.
4.
Tighten drain plug to the specified torque. Refer to
Refilling
INFOID:0000000009948868
1.
Remove filler plug (1) and gasket from transaxle case.
2.
Fill with new gear oil until oil level reaches the specified limit at
filler plug mounting hole as shown in the figure.
3.
After refilling gear oil, check the oil level. Refer to
4.
Set a gasket on filler plug and then install it to transaxle case.
CAUTION:
Never reuse gasket.
5.
Tighten filler plug to the specified torque. Refer to
SCIA7623E
SCIA7622E
Oil grade and
viscosity
MA-10, "Fluids and Lubricants"
.
Oil capacity
TM-63, "General Specification"
.
SCIA7623E
TM-18
< REMOVAL AND INSTALLATION >
[6MT: RS6F94R]
SIDE OIL SEAL
REMOVAL AND INSTALLATION
SIDE OIL SEAL
Removal and Installation
INFOID:0000000009948869
REMOVAL
1.
Remove front drive shafts. Refer to
FAX-16, "LEFT SIDE : Removal and Installation"
"RIGHT SIDE : Removal and Installation"
2.
Remove differential side oil seals (1) from clutch housing and
transaxle case, using a suitable tool.
CAUTION:
Never damage transaxle case and clutch housing.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Install differential side oil seals (1) to clutch housing and transaxle
case, using the drift [Stamping number: B.vi 1666-B] of the drift set
[SST: KV32500QAA ( - )].
CAUTION:
• Never incline differential side oil seal.
• Never damage clutch housing and transaxle case.
Inspection
INFOID:0000000009948870
INSPECTION AFTER INSTALLATION
Check the oil leakage and the oil level. Refer to
SCIA7625E
A
: Transaxle case side
B
: Clutch housing side
Dimension “L
1
”
: 1.2 – 1.8 mm (0.047 – 0.071 in)
Dimension “L
2
”
: 2.7 – 3.3 mm (0.106 – 0.130 in)
JPDIC0454ZZ
CONTROL LINKAGE
TM-19
< REMOVAL AND INSTALLATION >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
CONTROL LINKAGE
Exploded View
INFOID:0000000009948871
Removal and Installation
INFOID:0000000009948872
REMOVAL
1.
Pull the shifter lever knob upward to remove.
2.
Remove center console assembly. Refer to
IP-23, "Removal and Installation"
.
3.
Remove harness clips.
4.
Shift the shifter lever in the neutral position.
5.
Remove mounting bolts of the M/T shift selector.
6.
Remove air duct (inlet). Refer to
EM-24, "Removal and Installation"
7.
Remove battery. Refer to
PG-82, "Removal and Installation"
1.
Bracket
2.
Shifter cable
3.
Shifter lever A
4.
Selector lever
5.
Selector cable
6.
Tapping bolt
7.
Cable mounting bracket
8.
Lock plate
9.
M/T shift selector
10. Shifter lever
11.
Shifter lever knob
Refer to
for the symbols in the figure.
JPDIC0649GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст