Nissan Cube. Manual — part 1033
TIRE PRESSURE SENSOR WAKE UP OPERATION
WT-23
< BASIC INSPECTION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
TIRE PRESSURE SENSOR WAKE UP OPERATION
Description
INFOID:0000000009949853
This procedure must be done after replacement of a tire pressure sensor, BCM, or rotation of wheels.
Work Procedure
INFOID:0000000009949854
1.
TIRE PRESSURE SENSOR WAKE-UP PROCEDURE
1.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
NOTE:
The position of an inactive tire pressure sensor can be identified by checking the blinking timing of the low
tire pressure warning lamp.
2.
Contact the tire pressure sensor activation tool (J-45295) (1) to
the side of the tire at the location to the tire pressure sensor.
3.
Press and hold the tire pressure sensor activation tool button
while pushing the tool to the tire surface. (approximately for 5
seconds)
CAUTION:
Perform the wake-up procedure starting from the vehicle
front left wheel, then repeat the procedure in the order of
the front right wheel, rear right wheel, and rear left wheel.
4.
Check that the turn signal lamps blink twice when the tire pres-
sure sensor wake-up procedure for all wheels is completed.
5.
Check that the low tire pressure warning lamp turns OFF, after
the tire pressure sensor wake-up procedure is completed for all wheels and turns OFF.
Is the tire pressure sensor wake-up procedure completed?
YES
>> Perform the tire pressure sensor ID registration procedure. Refer to
NO
>> Perform trouble diagnosis for the tire pressure sensor. Refer to
.
JPEIC0089GB
NNEIC0020ZZ
WT-24
< BASIC INSPECTION >
ID REGISTRATION PROCEDURE
ID REGISTRATION PROCEDURE
Description
INFOID:0000000009949855
This procedure must be done after replacing or rotating wheels, replacing tire pressure sensor or BCM.
Work Procedure
INFOID:0000000009949856
1.
TIRE PRESSURE SENSOR ID REGISTRATION PROCEDURE
CAUTION:
To perform ID registration, observe the following points:
• Never register ID in a place where radio waves are interfered (e.g. radio tower).
• Never register ID in a place close to vehicles including TPMS.
With CONSULT
Display the “WORK SUPPORT” screen and select “ID REGIST”.
Is the tire pressure sensor activation tool (J-45295) used for the tire pressure sensor ID registration proce-
dure?
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
TIRE PRESSURE SENSOR ID REGISTRATION PROCEDURE (WITH TIRE PRESSURE SENSOR ACTI-
VATION TOOL)
1.
Turn the ignition switch ON.
2.
Select the start button on the “ID REGIST” screen.
3.
Contact the tire pressure sensor activation tool (J-45295) (1) to
the side of the tire at the location to the tire pressure sensor.
4.
Press and hold the tire pressure sensor activation tool button
while pushing the tool to the tire surface. (approximately for 5
seconds)
CAUTION:
Perform the ID registration procedure starting from the
vehicle front left wheel, then repeat the procedure in the
order of the front right wheel, rear right wheel, and rear left
wheel.
5.
When ID registration is completed, check the following pattern at each wheel.
6.
After the ID registration procedure for all wheels is completed, press “END” to end ID registration, and
check that ID registration for all wheels is completed.
Is the check result normal?
YES
>> ID registration END.
NO
>> Refer to
3.
TIRE PRESSURE SENSOR ID REGISTRATION PROCEDURE (WITHOUT TIRE PRESSURE SENSOR
ACTIVATION TOOL)
1.
Adjust the tire pressure for all wheels to match the list below.
NNEIC0020ZZ
Sequence
ID registration position
Turn signal lamp
CONSULT
1
Front left wheel
2 blinks
“Red”
↓
“Green”
2
Front right wheel
3
Rear right wheel
4
Rear left wheel
ID REGISTRATION PROCEDURE
WT-25
< BASIC INSPECTION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
2.
Drive the vehicle at a speed at more than 40 km/h (25 MPH) for 3 minutes or more, then perform the tire
pressure sensor ID registration procedure.
3.
After ID registration for all wheels is completed, press “END” to end ID registration.
4.
Adjust the tire pressures for all wheels to the specified value. Refer to
.
Is ID registrations for all wheels completed?
YES
>> ID registration END.
NO
>> Performs trouble-diagnosis of the Tire Pressure Monitoring System (TPMS). Refer to
(With intelligent key system),
(Without intelligent key sys-
tem).
Tire position
Tire pressure kPa (kg/cm
2
, psi)
Front LH
240 (2.4, 35)
Front RH
220 (2.2, 32)
Rear RH
200 (2.0, 29)
Rear LH
180 (1.8, 26)
ID registration position
CONSULT
Front LH
“Red”
↓
“Green”
Front RH
Rear RH
Rear LH
WT-26
< DTC/CIRCUIT DIAGNOSIS >
C1704, C1705, C1706, C1707 LOW TIRE PRESSURE
DTC/CIRCUIT DIAGNOSIS
C1704, C1705, C1706, C1707 LOW TIRE PRESSURE
Description
INFOID:0000000009949857
When the tire pressure monitoring system detects low inflation pressure, the low tire pressure warning lamps
in the combination meter comes on.
DTC Logic
INFOID:0000000009949858
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
DTC REPRODUCTION PROCEDURE
With CONSULT
1.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
2.
Check the tire pressure for all wheels and adjust to the specified value. Refer to
.
3.
Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.
Is DTC “C1704”, “C1705”, “C1706”, “C1707” detected?
YES
>> Perform trouble diagnosis. Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009949859
1.
CHECK TIRE PRESSURE
Check the internal pressure of all wheels. Refer to
.
Is the inspection result normal?
YES
>> Replace the DTC-detected malfunctioning tire pressure sensor. Refer to
GENT KEY : Removal and Installation"
(With intelligent key system),
GENT KEY : Removal and Installation"
(Without intelligent key system).
NO
>> After adjusting the air pressure, GO TO 2.
2.
CHECK TIRE PRESSURE SIGNAL
With CONSULT
1.
Drive for 3 minutes at a speed of 40 km/h (25 MPH) or more, then drive normally for 10 minutes.
2.
Perform “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.
3.
Select “BCM” in “DATA MONITOR”, and check that the tire pressures match the standard value.
DTC
Display item
Malfunction detected condition
Possible cause
C1704
LOW PRESSURE FL
Front LH tire pressure drops to 182.7 kPa (1.9 kg/cm
2
, 26 psi) or less.
[NOTE]
• Low tire pressure
• Tire pressure sen-
sor malfunction
C1705
LOW PRESSURE FR
Front RH tire pressure drops to 182.7 kPa (1.9 kg/cm
2
, 26 psi) or less.
[NOTE]
C1706
LOW PRESSURE RR
Rear RH tire pressure drops to 182.7 kPa (1.9 kg/cm
2
, 26 psi) or less.
[NOTE]
C1707
LOW PRESSURE RL
Rear LH tire pressure drops to 182.7 kPa (1.9 kg/cm
2
, 26 psi) or less.
[NOTE]
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст