Nissan Cube. Manual — part 65
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-109
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ACTIVE TEST
WORK SUPPORT
HEADLAMP
HEADLAMP : CONSULT Function (BCM - HEAD LAMP)
INFOID:0000000010249179
WORK SUPPORT
Test item
Description
INT LAMP
This test is able to check interior room lamp operation
• On: Operate
• Off: Non-operation
FLASHER
This test is able to check flasher operation [LH/RH/Off]
HORN
This test is able to check horn operation
• On: Operate
Test item
Description
REMO CONT IN REGIST
Keyfob ID code can be registered
REMO CONT IN ERASUR
Keyfob ID code can be erased
REMO CONT IN CONFIR
It can be checked whether Intelligent Key ID code is registered or not in this mode
MULTI ANSWER BACK SET
NOTE:
This item is displayed, but cannot be tested
HORN CHIRP SET
Hazard and horn reminder function (horn operation) mode can be changed in this mode
• On: Operate
• Off: Non-operation
HAZARD LAMP SET
Hazard and horn reminder function (hazard operation) mode can be changed in this mode
• MODE1: Non-operation
• MODE2: Unlock operation only
• MODE3: Lock operation only
• MODE4: Lock and unlock operation
AUTO LOCK SET
Auto door lock time can be changed in this mode
• MODE 1: Non-operation
• MODE 2: 30 sec
• MODE 3: 1 minute
• MODE 4: 2 minute
• MODE 5: 3 minute
• MODE 6: 4 minute
• MODE 7: 5 minute
PANIC ALARM SET
Panic alarm button pressing time on keyfob remote control button can be selected from the
following with this mode
• MODE1: 0.5 sec
• MODE2: Non-operation
• MODE3: 1.5 sec
TRUNK OPEN SET
NOTE:
This item is displayed, but cannot be tested
Service item
Setting
item
Setting
BATTERY SAVER SET
On*
With the exterior lamp battery saver function
Off
Without the exterior lamp battery saver function
BCS-110
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
*: Factory setting
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
ILL DELAY SET
MODE 1
NOTE:
This item is displayed, but cannot be used
MODE 2
MODE 3
MODE 4
MODE 5
MODE 6
MODE 7
MODE 8
AUTO LIGHT LOGIC SET
MODE 1
NOTE:
This item is displayed, but cannot be used
MODE 2
MODE 3
MODE 4
MODE 5
MODE 6
Service item
Setting
item
Setting
Monitor item
[Unit]
Description
IGN ON SW
[On/Off]
Indicated [On/Off] condition of ignition switch in ON position
ACC ON SW
[On/Off]
Indicates [On/Off] condition of ignition switch in ACC position
HI BEAM SW
[On/Off]
Each switch status that BCM judges from the combination switch reading function
HEAD LAMP SW 1
[On/Off]
HEAD LAMP SW 2
[On/Off]
TAIL LAMP SW
[On/Off]
AUTO LIGHT SW*
[On/Off]
PASSING SW
[On/Off]
FR FOG SW*
[On/Off]
DOOR SW-DR
[On/Off]
Indicated [On/Off] condition of front door switch (driver side)
DOOR SW-AS
[On/Off]
Indicated [On/Off] condition of front door switch (passenger side)
DOOR SW-RR
[On/Off]
Indicated [On/Off] condition of rear door switch RH
DOOR SW- RL
[On/Off]
Indicated [On/Off] condition of rear door switch LH
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-111
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
*: This item is displayed, but cannot be monitored.
ACTIVE TEST
WIPER
WIPER : CONSULT Function (BCM - WIPER)
INFOID:0000000010249183
WORK SUPPORT
*:Factory setting
DATA MONITOR
NOTE:
BACK DOOR SW
[On/Off]
Indicated [On/Off] condition of back door switch
TURN SIGNAL R
[On/Off]
Each switch status that BCM judges from the combination switch reading function
TURN SIGNAL L
[On/Off]
KEY ON SW
[On/Off]
Indicated [On/Off] condition of key switch
KEYLESS LOCK
[On/Off]
Indicated [On/Off] condition of lock signal from key fob
PKB SW
[On/Off]
The parking brake switch status received from combination meter with CAN communica-
tion
ENGINE RUN
[On/Off]
The engine status received from ECM with CAN communication
VEHICLE SPEED
[km/h]
Display the vehicle speed signal received from combination meter by numerical value
[Km/h]
OPTI SEN (DTCT)
[V]
NOTE:
This item is displayed, but cannot be monitored
OPTI SEN (FILT)
[V]
NOTE:
This item is displayed, but cannot be monitored
Monitor item
[Unit]
Description
Test item
Operation
Description
TAIL LAMP
On
Transmits the position light request signal to IPDM E/R with CAN commu-
nication to turn the tail lamp ON.
Off
Stops the tail lamp request signal transmission.
HEAD LAMP
Hi
Transmits the high beam request signal with CAN communication to turn
the headlamp (HI).
Lo
Transmits the low beam request signal with CAN communication to turn the
headlamp (LO).
Off
Stops the high & low beam request signal transmission.
FR FOG LAMP
On
NOTE:
This item is displayed, but cannot be tested
Off
ILL DIM SIGNAL
On
NOTE:
This item is displayed, but cannot be tested
Off
Service item
Setting item
Description
WIPER SPEED
SETTING
On
With vehicle speed
(Front wiper intermittent time linked with the vehicle speed and wiper intermittent dial position)
Off*
Without vehicle speed
(Front wiper intermittent time linked with the wiper intermittent dial position)
BCS-112
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
ACTIVE TEST
FLASHER
FLASHER : CONSULT Function (BCM - FLASHER)
INFOID:0000000010249180
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Monitor Item
[Unit]
Description
IGN ON SW
[On/Off]
Ignition switch ON status judged from ignition power supply.
IGN SW CAN
[On/Off]
Ignition switch ON status received from IPDM E/R with CAN communication.
FR WIPER HI
[On/Off]
Each switch status that BCM judges from the combination switch reading function.
FR WIPER LOW
[On/Off]
FR WIPER INT
[On/Off]
FR WASHER SW
[On/Off]
INT VOLUME
[1
−
7]
Each switch status that BCM judges from the combination switch reading function.
FR WIPER STOP
[On/Off]
Front wiper motor (stop position) status received from IPDM E/R with CAN communication.
VEHICLE SPEED
[km/h]
The value of the vehicle speed signal received from combination meter with CAN communication.
RR WIPER ON
[On/Off]
Each switch status that BCM judges from the combination switch reading function.
RR WIPER INT
[On/Off]
RR WASHER SW
[On/Off]
REVERSE SW CAN
[On/Off]
NOTE:
The item is indicated, but not monitored.
RAIN SENSOR
[On/Off]
Test item
Operation
Description
FR WIPER
Hi
Transmits the front wiper request signal (HI) to IPDM E/R with CAN communication to
operate the front wiper HI operation.
Lo
Transmits the front wiper request signal (LO) to IPDM E/R with CAN communication to
operate the front wiper LO operation.
INT
Transmits the front wiper request signal (INT) to IPDM E/R with CAN communication to
operate the front wiper INT operation.
Off
Stops transmitting the front wiper request signal to stop the front wiper operation.
RR WIPER
On
Outputs the voltage to operate the rear wiper motor.
Off
Stops the voltage to stop.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст