Nissan Cube. Manual — part 795
SE-12
< REMOVAL AND INSTALLATION >
FRONT SEAT
REMOVAL AND INSTALLATION
FRONT SEAT
Exploded View
INFOID:0000000009950073
DRIVER'S SEAT
1.
Head rest
2.
Seatback trim
3.
Seatback pad
4.
Armrest cap
5.
Armrest assembly
6.
Bush
7.
Seat cushion assembly
8.
Seat cushion inner finisher
9.
Seat belt buckle
10. Reclining device inner cover (front)
11.
Reclining device inner cover (rear)
12. TORX bolt
JMJIA9531GB
FRONT SEAT
SE-13
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
PASSENGER'S SEAT
13. Seat cushion frame
14. Lifter link
15. Seat cushion outer finisher
16. Lifter lever knob
17. Lifter lever knob cap
18. Reclining lever knob
19. Reclining device outer cover (rear)
20. Reclining device outer cover (front)
21. TORX bolt
22. Seat slid outer cover
23. Seat slid inner cover
24. Seat cushion mat
25. Seat cushion silencer
26. Side air bag module
27. Seatback silencer
28. Headrest holder (free)
29. Headrest holder (locked)
30. Seatback frame
Refer to
1.
Headrest
2.
Seatback silencer
3.
Side air bag module
4.
Seat cushion silencer
5.
Reclining lever knob
6.
Seat cushion outer finisher
JMJIA9532GB
SE-14
< REMOVAL AND INSTALLATION >
FRONT SEAT
Removal and Installation
INFOID:0000000009950074
REMOVAL
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
1.
Remove the headrest.
2.
Remove the mounting bolts on the front side of the front seat.
3.
Remove the mounting bolts on the rear side of the front seat.
4.
Set seatback in a standing position.
5.
Disconnect harness connector under the seat and remove harness securing clips.
CAUTION:
Before removal, turn ignition switch OFF, disconnect battery negative terminal and then wait for at
least 3 minutes.
6.
Remove seat from the vehicle.
CAUTION:
• When removing and installing, use shop cloths to protect parts from damage.
• When removing and installing, 2 workers are required so as to prevent it from dropping.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Before installation, turn ignition switch OFF, disconnect battery negative terminal and then wait for
at least 3 minutes.
• Clamp the harness in position.
NOTE:
After installing the passenger seat, perform zero point reset. Refer to
SRC-9, "ZERO POINT RESET : Descrip-
.
Disassembly and Assembly
INFOID:0000000009950075
DISASSEMBLY
1.
Remove the armrest assembly.
• Remove the armrest cap.
• Remove the mounting bolt, and then remove armrest assembly.
2.
Remove the seatback trim and seatback pad.
• Remove seatback retainer installed in the lower portion of seat cushion.
• Remove harness installed in the lower portion of seat cushion
• Remove the seatback retainer (1), and then open the fastener
(2).
7.
Reclining device outer cover (rear)
8.
Reclining device outer cover (front) 9.
Seat cushion frame
10. Occupant detection system control unit 11.
TORX bolt
12. Reclining device inner cover (rear)
13. Reclining device inner cover (front)
14. Seat belt buckle
15. Seat cushion inner finisher
16. Seat cushion assembly
17. Seatback pad
18. Seatback trim
19. Headrest holder (locked)
20. Headrest holder (free)
21. Seatback frame
22. Seat cushion mat
23. TORX bolt
Refer to
for symbols in the figure.
JMJIA2934ZZ
FRONT SEAT
SE-15
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
• Remove the seatback retainer from seatback inside.
• Remove the headrest holder.
CAUTION:
Before installing headrest holder check its orientation.
(front/rear and right/left)
• Remove the side air bag module mounting nuts.
• Remove the seatback trim and seatback pad from the seatback frame.
• Remove the hog rings, and separate the seatback trim and seatback pad.
3.
Remove the seatback silencer.
4.
Remove the seat cushion outer finisher.
• Remove the pawls, and then lifter lever knob finisher (1).
(Driver's seat only)
• Remove the mounting screws, and remove the lifter lever (2).
(Driver's seat only)
• Pull out the reclining lever while holding and raising the pawl.
• Remove the metal clip and pawls, and then pull out seat cush-
ion outer finisher outside.
PIIB4084J
: Pawl
JMJIA3131ZZ
: Pawl
JMJIA2935ZZ
: Metal clip
: Pawl
JMJIA3132ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст