Nissan Murano Z51 (2013 year). Manual — part 96
C1708, C1709, C1710, C1711 TIRE PRESSURE SENSOR
WT-23
< DTC/CIRCUIT DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
4.
Check the continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace damaged parts.
3.
CHECK TIRE PRESSURE RECEIVER POWER SUPPLY CIRCUIT
1.
Connect the BCM harness connector.
2.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
3.
Check the voltage between the BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace damaged parts.
4.
CHECK TIRE PRESSURE RECEIVER
Check tire pressure receiver. Refer to
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace tire pressure receiver. Refer to
WT-48, "Removal and Installation"
.
5.
CHECK ID REGISTRATION
Perform ID registration of all tire pressure sensors. Refer to
Can ID registration of all tire pressure sensors be completed?
YES
>> GO TO 6.
NO
>> Replace tire pressure sensor. Refer to
6.
CHECK TIRE PRESSURE MONITORING SYSTEM
With CONSULT
1.
Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.
2.
Perform “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.
3.
Select “BCM” in “DATA MONITOR”, and check that the tire pressures match the standard value.
BCM
Tire pressure receiver
Continuity
Connector
Terminal
Connector
Terminal
M123
137
M21
1
Existed
138
4
139
2
BCM
—
Continuity
Connector
Terminal
M123
137
Ground
Not existed
138
139
BCM
—
Voltage
(Approx.)
Connector
Terminal
M123
138
Ground
5 V
Revision: 2012 September
2013 MURANO
WT-24
< DTC/CIRCUIT DIAGNOSIS >
C1708, C1709, C1710, C1711 TIRE PRESSURE SENSOR
CAUTION:
Stop the vehicle and within 15 minutes, use “DATA MONITOR” in “AIR PRESSURE MONITOR” of
“BCM” to read the tire pressure for all wheels.
Is the inspection result normal?
YES
>> Replace the DTC-detected malfunctioning tire pressure sensor. Refer to
.
NO
>> Replace BCM. Refer to
Monitor item
Condition
Displayed value
AIR PRESS FL
Drive at a speed of 40 km/h (25 MPH) or more, for several
minutes without stopping.
Internal pressure of tires
AIR PRESS FR
AIR PRESS RR
AIR PRESS RL
Revision: 2012 September
2013 MURANO
C1716, C1717, C1718, C1719 TIRE PRESSURE SENSOR
WT-25
< DTC/CIRCUIT DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
C1716, C1717, C1718, C1719 TIRE PRESSURE SENSOR
DTC Logic
INFOID:0000000008454507
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
DTC REPRODUCTION PROCEDURE
With CONSULT
1.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
2.
Check the tire pressure for all wheels and adjust to the specified value. Refer to
.
3.
Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.
Is DTC “C1716”, “C1717”, “C1718”, “C1719” detected?
YES
>> Perform trouble diagnosis. Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000008454508
1.
CHECK TIRE PRESSURE
Check the internal pressure of all wheels. Refer to
.
Is the inspection result normal?
YES
>> Replace the DTC-detected malfunctioning tire pressure sensor. Refer to
.
NO
>> After adjusting the tire pressure, GO TO 2.
2.
CHECK TIRE PRESSURE SIGNAL
With CONSULT
1.
Check and adjust the tire pressure for all wheels. Refer to
.
2.
Perform tire pressure sensor ID registration for all wheels. Refer to
.
3.
Drive for 3 minutes at a speed of 40 km/h (25 MPH) or more, then drive normally for 10 minutes.
4.
Perform “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.
5.
Select “BCM” in “DATA MONITOR”, and check that the tire pressures match the standard value.
CAUTION:
Stop the vehicle and within 15 minutes, use CONSULT “DATA MONITOR” to display the tire pres-
sure for all wheels.
6.
Check that “DATA MONITOR” displays tire pressure of 438.60 kPa (4.47 kg/cm
2
, 63.60 Psi).
Is the inspection 438.60 kPa (4.47 kg/cm
2
, 63.60 Psi)?
YES
>> Replace tire pressure sensor the tire pressure 438.60 kPa (4.386 bar, 4.47 kg/cm
2
, 63.60 Psi) dis-
.
NO
>> GO TO 1.
DTC
Display item
Malfunction detected condition
Possible case
C1716
[PRESSDATA ERR] FL
Malfunction in the tire pressure data from the front left
wheel tire pressure sensor.
• ID registration is not fin-
ished
• Tire pressure sensor mal-
function
C1717
[PRESSDATA ERR] FR
Malfunction in the tire pressure data from the front right
wheel tire pressure sensor.
C1718
[PRESSDATA ERR] RR
Malfunction in the tire pressure data from the rear right
wheel tire pressure sensor.
C1719
[PRESSDATA ERR] RL
Malfunction in the tire pressure data from the rear left wheel
tire pressure sensor.
Revision: 2012 September
2013 MURANO
WT-26
< DTC/CIRCUIT DIAGNOSIS >
C1729 VEHICLE SPEED SIGNAL
C1729 VEHICLE SPEED SIGNAL
Description
INFOID:0000000008454509
BCM detects no vehicle speed signal.
DTC Logic
INFOID:0000000008454510
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
DTC REPRODUCTION PROCEDURE
With CONSULT
1.
Drive for several minutes at a speed of 40 km/h (25 MPH) or more, then stop the vehicle.
2.
Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.
Is DTC “C1729” detected?
YES
>> Perform trouble diagnosis. Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000008454511
1.
PERFORM COMBINATION METER SELF-DIAGNOSIS
With CONSULT
Perform “SELF-DIAG RESULTS” of “METER/M&A”.
Is any DTC detected?
YES
>> Check the DTC. Refer to
.
NO
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.
Is DTC “C1729” detected?
YES
>> Replace BCM. Refer to
WT-8, "COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)"
NO
>> GO TO 3.
3.
CHECK INFORMATION
With CONSULT
1.
Perform “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.
2.
Select “BCM” in “DATA MONITOR”, and check the input/output values. Refer to
Is the inspection result normal?
YES
>> Check pin terminal and connection of each harness connector for malfunctioning conditions.
NO
>> Replace BCM. Refer to
DTC
Display item
Malfunction detected condition
Possible case
C1729
VHCL SPEED SIG ERR
Vehicle speed signal not detected.
• CAN communication error
• Combination meter malfunction
Revision: 2012 September
2013 MURANO
C1734 BCM
WT-27
< DTC/CIRCUIT DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
C1734 BCM
DTC Logic
INFOID:0000000008454512
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
DTC REPRODUCTION PROCEDURE
With CONSULT
1.
Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.
2.
Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.
CAUTION:
Perform within 15 minutes after stop the vehicle.
Is DTC “C1734” detected?
YES
>> Perform trouble diagnosis. Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000008454513
1.
CHECK BCM POWER SUPPLY
1.
Turn the ignition switch OFF.
2.
Disconnect BCM harness connector.
3.
Check voltage between BCM harness connector terminals and ground.
Is the power supply normal?
YES
>> GO TO 2.
NO
>>
Check the following. If any items are damaged, repair or replace damage parts.
• 40A fusible link [No. L located in the fuse block]. Refer to
PG-113, "Fuse and Fusible Link
.
• 10A fuse [No. 10 located in the fuse block (J/B)]. Refer to
PG-112, "Fuse, Connector and Termi-
• Harness for short or open between battery and BCM harness connector M118 terminal 1.
• Harness for short or open between battery and BCM harness connector M119 terminal 11.
• Check the Battery voltage.
2.
CHECK BCM GROUND
Check the continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace damaged parts.
3.
CHECK HARNESS BETWEEN BCM AND TIRE PRESSURE RECEIVER
1.
Disconnect tire pressure receiver harness connector.
2.
Check the continuity between BCM harness connector and tire pressure receiver harness connector.
DTC
Display item
Malfunction detected condition
Possible case
C1734
CONTROL UNIT
Tire pressure monitoring system malfunction in BCM
BCM malfunction
BCM
—
Voltage
(Approx.)
Connector
Terminal
M118
1
Ground
Battery voltage
M119
11
BCM
—
Continuity
Connector
Terminal
M119
13
Ground
Existed
Revision: 2012 September
2013 MURANO
WT-28
< DTC/CIRCUIT DIAGNOSIS >
C1734 BCM
3.
Check the continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace damaged parts.
4.
CHECK BCM
Check the BCM input/output signal. Refer to
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 5.
5.
CHECK BCM HARNESS CONNECTOR
Check the BCM pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
NO
>> Check for looseness or damage at the harness connector pins of the low tire pressure warning
control unit. Repair or replace if necessary.
BCM
Tire pressure receiver
Continuity
Connector
Terminal
Connector
Terminal
M123
137
M21
1
Existed
138
4
139
2
BCM
—
Continuity
Connector
Terminal
M123
137
Ground
Not existed
138
139
Revision: 2012 September
2013 MURANO
TIRE PRESSURE RECEIVER
WT-29
< DTC/CIRCUIT DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
TIRE PRESSURE RECEIVER
Component Function Check
INFOID:0000000008454514
1.
TIRE PRESSURE MONITORING SYSTEM OPERATION
With CONSULT
1.
Drive for 3 minutes at a speed of 40 km/h (25 MPH) or more, then drive normally for 10 minutes.
2.
On “DATA MONITOR”, select “AIR PRESS FL”, “AIR PRESS FR”, “AIR PRESS RR” and “AIR PRESS
RL”, and check that the tire pressures match the standard value.
CAUTION:
Stop the vehicle and within 5 minutes, use CONSULT “DATA MONITOR” to display the tire pressure for
all wheels.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Perform trouble diagnosis. Refer to
Diagnosis Procedure
INFOID:0000000008454515
1.
CHECK TIRE PRESSURE RECEIVER SIGNAL
1.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
2.
Check tire pressure receiver connector and ground signal with oscilloscope.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
CHECK TIRE PRESSURE RECEIVER INPUT VOLTAGE
1.
Turn the ignition switch OFF.
2.
Disconnect tire pressure receiver connector.
3.
Turn the ignition switch ON.
Monitor item
Condition
Displayed value
AIR PRESS FL
Drive for 3 minutes at a speed of 40 km/h (25 MPH) or
more, then drive normally for 10 minutes.
Internal pressure of tires
AIR PRESS FR
AIR PRESS RR
AIR PRESS RL
Tire pressure receiver
—
Condition
Voltage
(Approx.)
Connector
Terminal
M21
2
Ground
Stand by state
When receiving the signal from the tire
pressure sensor
OCC3881D
OCC3880D
Revision: 2012 September
2013 MURANO
WT-30
< DTC/CIRCUIT DIAGNOSIS >
TIRE PRESSURE RECEIVER
CAUTION:
Never start the engine.
4.
Check voltage between tire pressure receiver connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace damaged parts.
3.
CHECK TIRE PRESSURE RECEIVER GROUND CIRCUIT
1.
Turn the ignition switch OFF.
2.
Disconnect BCM harness connector.
3.
Check continuity between BCM harness connector and tire pressure receiver connector.
4.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace damaged parts.
4.
CHECK BCM CIRCUIT
Inspect the BCM circuit. Refer to
.
Is the BCM circuit normal?
YES
>> Replace tire pressure receiver. Refer to
WT-48, "Removal and Installation"
NO
>> Replace BCM. Refer to
Tire pressure receiver
—
Voltage
(Approx.)
Connector
Terminal
M21
4
Ground
5.0 V
BCM
Tire pressure receiver
Continuity
Connector
Terminal
Connector
Terminal
M123
137
M21
1
Existed
BCM
—
Continuity
Connector
Terminal
M123
137
Ground
Not existed
Revision: 2012 September
2013 MURANO
LOW TIRE PRESSURE WARNING LAMP
WT-31
< DTC/CIRCUIT DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
LOW TIRE PRESSURE WARNING LAMP
Component Function Check
INFOID:0000000008454516
1.
CHECK THE ILLUMINATION OF THE LOW TIRE PRESSURE WARNING LAMP
Check that the low tire pressure warning lamp is turned OFF after illuminating for approximately 1 second,
when the ignition switch is turned ON.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Perform trouble diagnosis. Refer to
Diagnosis Procedure
INFOID:0000000008454517
1.
POWER SUPPLY AND GROUND CIRCUIT
Check power supply and ground circuit. Refer to
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace damaged parts.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.
Is any DTC detected?
YES
>> Check the DTC. Refer to
.
NO
>> GO TO 3.
3.
CHECK LOW TIRE PRESSURE WARNING LAMP SIGNAL
With CONSULT
1.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
2.
Perform “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.
3.
Select “BCM” in “DATA MONITOR”, and check that the low tire pressure warning lamp is turned OFF after
illuminating for approximately 1 second, when the ignition switch is turned ON.
Is the inspection result normal?
YES
>> Check the combination meter. Refer to
MWI-6, "METER SYSTEM : System Description"
NO
>> Replace the BCM. Refer to
Revision: 2012 September
2013 MURANO
WT-32
< DTC/CIRCUIT DIAGNOSIS >
POWER SUPPLY AND GROUND CIRCUIT
POWER SUPPLY AND GROUND CIRCUIT
Diagnosis Procedure
INFOID:0000000008454518
1.
POWER SUPPLY SYSTEM CHECK
1.
Turn the ignition switch OFF.
2.
Disconnect the BCM harness connector.
3.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
4.
Check the voltage between the BCM harness connector and the ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace damaged parts.
2.
GROUND SYSTEM INSPECTION
1.
Turn the ignition switch OFF.
2.
Check the continuity between the BCM harness connector and the ground.
Is the inspection result normal?
YES
>> • Check the 10A fuse [No. 10 in fuse block (J/B)].
• Check the 40A fusible link [No. L in fuse block].
NO
>> Repair or replace damaged parts.
BCM
—
Voltage
Connector
Terminal
M118
1
Ground
Battery voltage
M119
11
BCM
—
Continuity
Connector
Terminal
M119
13
Ground
Existed
Revision: 2012 September
2013 MURANO
TPMS
WT-33
< SYMPTOM DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
SYMPTOM DIAGNOSIS
TPMS
Symptom Table
INFOID:0000000008454519
LOW TIRE PRESSURE WARNING LAMP SYMPTOM CHART
Revision: 2012 September
2013 MURANO
WT-34
< SYMPTOM DIAGNOSIS >
TPMS
Diagnosis items
Symptom
(Ignition switch
ON)
Low tire pressure warning lamp
Cause
Action
Low tire pres-
sure warning
lamp
The low tire pres-
sure warning lamp
illuminates for 1
second, then turns
OFF.
Wake-up operation for all
tire pressure sensors at
wheels is completed.
No system malfunctions
The low tire pres-
sure warning lamp
repeats blinking
ON for 2 seconds
and OFF for 0.2
seconds.
Wake-up operation for all
tire pressure sensors at
wheels is not completed.
Perform the wake-up oper-
ation for all tire pressure
sensors at wheels. Refer to
.
The low tire pres-
sure warning lamp
blinks once.
The front left tire pres-
sure sensor is not acti-
vated.
Perform the wake-up oper-
ation for the tire pressure
sensor at front left wheel.
Refer to
The low tire pres-
sure warning lamp
repeats blinking
twice.
The front right tire pres-
sure sensor is not acti-
vated.
Perform the wake-up oper-
ation for the tire pressure
sensor at front right wheel.
Refer to
The low tire pres-
sure warning lamp
repeats blinking for
3 times.
The rear right tire pres-
sure sensor is not acti-
vated.
Perform the wake-up oper-
ation for the tire pressure
sensor at rear right wheel.
Refer to
The low tire pres-
sure warning lamp
repeats blinking for
4 times.
The rear left tire pressure
sensor is not activated.
Perform the wake-up oper-
ation for the tire pressure
sensor at rear left wheel.
Refer to
The low tire pres-
sure warning lamp
turns ON and stays
illuminated.
Low tire pressure
Check the tire pressure for
all wheels and adjust to the
specified value. Refer to
.
SEIA0592E
SEIA0593E
JPEIC0090GB
SEIA0595E
SEIA0596E
SEIA0597E
SEIA0598E
Revision: 2012 September
2013 MURANO
TPMS
WT-35
< SYMPTOM DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
NOTE:
If tire pressure sensor wake-up operation is not completed for two or more tire pressure sensors, the applica-
ble low tire pressure warning lamp blinking patterns are displayed continuously.
(Example: Blinks once/OFF/blinks 3 times = Wake-up operation is not completed at the front left wheel and
rear right wheel tire pressure sensors.)
Low tire pres-
sure warning
lamp
The low tire pres-
sure warning lamp
repeats blinking at
0.5-second inter-
vals for 1 minute,
and then stays illu-
minated.
The combination meter
fuse is open or removed
(or pulled out).
Check and install the com-
bination meter fuse. If nec-
essary, replace the fuse.
The low tire pressure
warning control unit har-
ness connector is re-
moved.
Check the connection con-
ditions of the low tire pres-
sure warning control unit
harness connector, and re-
pair if necessary.
Tire Pressure Monitoring
System (TPMS) mal-
function.
• Perform CONSULT self-
diagnosis. Refer to
"AIR PRESSURE MONI-
TOR : CONSULT Func-
tion (BCM - AIR
PRESSURE MONI-
TOR)"
• If necessary, perform tire
pressure sensor ID regis-
tration. Refer to
.
Hazard warning
lamp
The hazard warn-
ing lamp does not
blink twice when
the tire pressure
sensor is activated.
—
1.
The tire pressure
sensor activation
tool (J-45295) does
not activate.
2.
The ignition switch
is OFF when the
tire pressure sen-
sor wake-up opera-
tion is performed.
3.
The tire pressure
sensor activation
tool (J-45295) is
not used in the cor-
rect position.
4.
The tire pressure
sensor is already
waked up.
1.
Replace the battery in
the tire pressure sen-
sor activation tool (J-
45295).
2.
Turn the ignition
switch ON when per-
forming the tire pres-
sure sensor wake-up
operation.
3.
Operate the tire pres-
sure sensor activation
tool (J-45295) in the
correct position when
performing the wake-
up operation.
4.
No procedure.
Diagnosis items
Symptom
(Ignition switch
ON)
Low tire pressure warning lamp
Cause
Action
SEIA0788E
Revision: 2012 September
2013 MURANO
WT-36
< SYMPTOM DIAGNOSIS >
LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN ON
LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN ON
Description
INFOID:0000000008454520
The low tire pressure warning lamp does not illuminate when the ignition switch is turned ON.
NOTE:
The low tire pressure warning lamp illuminates for approximately 1 second and then turns OFF when the igni-
tion switch is turned ON. This is to check that no abnormal condition is present in the tire pressure monitoring
system.
The lamp bulb may be burnt out or the tire pressure monitoring system may be malfunctioning if the low tire
pressure warning lamp does not illuminate when the ignition switch is turned ON.
Diagnosis Procedure
INFOID:0000000008454521
1.
CHECK LOW TIRE PRESSURE WARNING LAMP
Perform trouble diagnosis of the low tire pressure warning lamp. Refer to
Is the inspection result normal?
YES
>> Check pin terminal and connection of each connector for damage and loose connection.
NO
>> Repair or replace damaged parts.
Revision: 2012 September
2013 MURANO
LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN OFF
WT-37
< SYMPTOM DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN OFF
Description
INFOID:0000000008454522
The low tire pressure warning lamp does not turn OFF after several seconds is passed after engine starts.
Diagnosis Procedure
INFOID:0000000008454523
1.
CHECK TIRE PRESSURE
1.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
2.
Check the tire pressure for all wheels and adjust to the specified value. Refer to
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Inspect or repair the tires or wheels.
2.
CHECK LOW TIRE PRESSURE WARNING LAMP
Check low tire pressure warning lamp display.
Does not low tire pressure warning lamp turn OFF?
YES
>> GO TO 3.
NO
>> INSPECTION END
3.
CHECK BCM
With CONSULT
Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.
Is any DTC detected?
YES
>> Check the DTC. Refer to
NO
>> GO TO 4.
4.
CHECK BCM POWER SUPPLY AND GROUND CIRCUIT
Perform the trouble diagnosis for power supply and ground circuit. Refer to
Is the inspection result normal?
YES
>> Replace BCM. Refer to
.
NO
>> Repair or replace error-detected parts.
Revision: 2012 September
2013 MURANO
WT-38
< SYMPTOM DIAGNOSIS >
LOW TIRE PRESSURE WARNING LAMP BLINKS
LOW TIRE PRESSURE WARNING LAMP BLINKS
Description
INFOID:0000000008454524
The low tire pressure warning lamp blinks when the ignition switch is turned ON.
NOTE:
The position of an inactive tire pressure sensor can be identified by checking the blinking timing of the low tire
pressure warning lamp.
Diagnosis Procedure
INFOID:0000000008454525
1.
TIRE PRESSURE SENSOR WAKE-UP OPERATION
Perform the tire pressure sensor wake-up. Refer to
.
Is the tire pressure sensor wake-up completed?
YES
>> GO TO 2.
NO
>> Perform trouble diagnosis for the tire pressure sensor. Refer to
.
2.
TIRE PRESSURE SENSOR ID REGISTRATION
Perform tire pressure sensor ID registration. Refer to
.
Is tire pressure sensor ID registration completed?
YES
>> INSPECTION END
NO
>> Perform the self-diagnosis for “AIR PRESSURE MONITOR”. Refer to
JPEIC0089GB
Revision: 2012 September
2013 MURANO
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст