Nissan Juke F15. Manual — part 991
DOOR MIRROR SYSTEM
MIR-7
< WIRING DIAGRAM >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
JRLWF5309GB
MIR-8
< WIRING DIAGRAM >
DOOR MIRROR SYSTEM
JRLWF5310GB
DOOR MIRROR REMOTE CONTROL SWITCH (MIRROR SWITCH/
CHANGEOVER SWITCH)
MIR-9
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
DTC/CIRCUIT DIAGNOSIS
DOOR MIRROR REMOTE CONTROL SWITCH (MIRROR SWITCH/
CHANGEOVER SWITCH)
Component Inspection
INFOID:0000000012201503
1.
CHECK MIRROR SWITCH & CHANGEOVER SWITCH
1. Turn ignition switch OFF.
2. Disconnect door mirror remote control switch connector.
3. Check door mirror remote control switch.
Is the inspection result normal?
YES
>> INSPECTION END.
NO
>> Replace door mirror remote control switch. Refer to
MIR-21, "Removal and Installation"
Door mirror remote control switch
condition
Continuity
Terminal
Change over
switch
Mirror switch
Driver side
13
6
LEFT
RIGHT
Existed
12
5
13
5
LEFT
12
6
13
2
UP
12
6
13
6
DOWN
12
2
Passenger side
13
7
RIGHT
RIGHT
12
4
13
4
LEFT
12
7
13
3
UP
12
7
13
7
DOWN
12
3
MIR-10
< SYMPTOM DIAGNOSIS >
SQUEAK AND RATTLE TROUBLE DIAGNOSES
SYMPTOM DIAGNOSIS
SQUEAK AND RATTLE TROUBLE DIAGNOSES
Work Flow
INFOID:0000000012201504
CUSTOMER INTERVIEW
Interview the customer if possible, to determine the conditions that exist when the noise occurs. Use the Diag-
nostic Worksheet during the interview to document the facts and conditions when the noise occurs and any
customer comments. Refer to
MIR-14, "Diagnostic Worksheet"
. This information is necessary to duplicate the
conditions that exist when the noise occurs.
• The customer may not be able to provide a detailed description or the location of the noise. Attempt to obtain
all the facts and conditions that exist when the noise occurs (or does not occur).
• If there is more than one noise in the vehicle, perform a diagnosis and repair the noise that the customer is
concerned about. This can be accomplished by performing a test drive with the customer.
• After identifying the type of noise, isolate the noise in terms of its characteristics. The noise characteristics
are provided so that the customer, service adviser, and technician use the same language when describing
the noise.
• Squeak – (Like tennis shoes on a clean floor)
Squeak characteristics include the light contact / fast movement / brought on by road conditions / hard sur-
faces = high-pitched noise / softer surfaces = low-pitched noises / edge to surface = chirping
• Creak – (Like walking on an old wooden floor)
Creak characteristics include firm contact / slow movement/twisting with a rotational movement / pitch
dependent on materials / often brought on by activity.
• Rattle – (Like shaking a baby rattle)
Rattle characteristics include fast repeated contact / vibration or similar movement / loose parts/missing clip
or fastener / incorrect clearance.
• Knock – (Like a knock on a door)
Knock characteristics include hollow sounds / sometimes repeating / often brought on by driver action.
• Tick – (Like a clock second hand)
Tick characteristics include gentle contacting of light materials / loose components / can be caused by driver
action or road conditions.
• Thump – (Heavy, muffled knock noise)
Thump characteristics include softer knock / dull sounds often brought on by activity.
• Buzz – (Like a bumblebee)
Buzz characteristics include high frequency rattle / firm contact.
• Often the degree of acceptable noise level varies depending upon the person. A noise that a technician may
judge as acceptable may be very irritating to a customer.
• Weather conditions, especially humidity and temperature, may have a great effect on noise level.
DUPLICATE THE NOISE AND TEST DRIVE
SBT842
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст