Nissan Juke F15. Manual — part 100
BR-60
< REMOVAL AND INSTALLATION >
REAR DISC BRAKE
Molykote is a registered trademark of Dow Corning Corporation.
BRAKE PAD : Removal and Installation
INFOID:0000000012200305
REMOVAL
WARNING:
Since dust covering the rear brake has an affect on human body, the dust must be removed with a
dust collector. Never splatter the dust with an air blow gun.
CAUTION:
• Never depress the brake pedal while removing the brake pads because the piston may pop out.
• If the brake fluid or grease adheres to the disc rotor, quickly wipe it off.
1. Remove tires with power tool.
2. Remove lower sliding pin bolt.
3. Suspend the cylinder body with suitable wire so that the brake
hose will not stretch.
4. Remove the brake pads, shims, shim covers and pad retainers from the torque member.
CAUTION:
• Never deform the pad retainer (2) when removing the pad
retainer from the torque member (1).
• Never damage the piston boot.
• Never drop the brake pads, shims, and the shim covers.
• Remember each position of the removed brake pads.
5. Perform inspection after removal. Refer to
1.
Sliding pin bolt
2.
Cylinder body
3.
Inner shim cover
4.
Inner shim
5.
Inner pad (with pad wear sensor)
6.
Pad retainer
7.
Torque member
8.
Outer pad
9.
Outer shim
1 Apply rubber grease.
2: Apply MOLYKOTE
®
AS880N or silicone-based grease.
: N·m (kg-m, ft-lb)
JSFIA0491ZZ
JSFIA0492ZZ
JPFIA0118ZZ
REAR DISC BRAKE
BR-61
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
INSTALLATION
Except NISMO RS
WARNING:
Since dust covering the rear brake has an affect on human body, the dust must be removed with a
dust collector. Never splatter the dust with an air blow gun.
CAUTION:
• Never depress the brake pedal while removing the brake pads or the cylinder body because the pis-
ton may pop out.
• If the brake fluid or grease adheres to the disc rotor, quickly wipe it off.
1. Install the pad retainers (1) to the torque member (2) if the pad
retainers has been removed.
CAUTION:
• Securely assemble the pad retainers so that it will not be
lifted up from the torque member.
• Never deform the pad retainers.
2. Apply MOLYKOTE
®
AS880N or silicone-based grease to the
mating faces (A) between the brake pads and the shims, and
install the shims and shim covers to the brake pad.
CAUTION:
Always replace the shim together with the shim cover when
replacing the brake pad.
Molykote is a registered trademark of Dow Corning Corporation.
3. Install the brake pads to the torque member.
4. Install cylinder body to torque member.
CAUTION:
• Never damage the piston boot.
• When replacing brake pad with new one, check a brake
fluid level in the reservoir tank because brake fluid returns to master cylinder reservoir tank
when pressing piston in.
NOTE:
Use a disc brake piston tool to easily press piston.
5. Install the lower sliding pin bolt and tighten it to the specified
torque.
6. Depress the brake pedal several times to check that no drag feel
is present for the rear disc brake. Refer to
7. Install tires. Refer to
WT-39, "Removal and Installation"
.
NISMO RS
WARNING:
Since dust covering the rear brake has an affect on human body, the dust must be removed with a
dust collector. Never splatter the dust with an air blow gun.
CAUTION:
• Never depress the brake pedal while removing the brake pads or the cylinder body because the pis-
ton may pop out.
• If the brake fluid or grease adheres to the disc rotor, quickly wipe it off.
PFIA0763J
JSFIA0493ZZ
JSFIA0491ZZ
BR-62
< REMOVAL AND INSTALLATION >
REAR DISC BRAKE
1. Install the pad retainers (1) to the torque member (2) if the pad
retainers has been removed.
CAUTION:
• Securely assemble the pad retainers so that it will not be
lifted up from the torque member.
• Never deform the pad retainers.
2. Apply MOLYKOTE
®
AS880N or silicone-based grease to the
mating faces (A) between the inner pad and the inner shim, and
install the inner shim and inner shim cover to the inner pad.
CAUTION:
Always replace the shim together with the shim cover when
replacing the brake pad.
Molykote is a registered trademark of Dow Corning Corporation.
3. Apply MOLYKOTE
®
AS880N or silicone-based grease to the
mating faces (A) between the outer pad and the outer shim, and
install the outer shim to the outer pad.
CAUTION:
Always replace the shim together with the shim cover when
replacing the brake pad.
Molykote is a registered trademark of Dow Corning Corporation.
4. Install the brake pads to the torque member.
5. Install cylinder body to torque member.
CAUTION:
• Never damage the piston boot.
• When replacing brake pad with new one, check a brake
fluid level in the reservoir tank because brake fluid returns to master cylinder reservoir tank
when pressing piston in.
NOTE:
Use a disc brake piston tool to easily press piston.
6. Install the lower sliding pin bolt and tighten it to the specified
torque.
7. Depress the brake pedal several times to check that no drag feel
is present for the rear disc brake. Refer to
8. Install tires. Refer to
WT-39, "Removal and Installation"
BRAKE PAD : Inspection
INFOID:0000000012200306
INSPECTION AFTER REMOVAL
• Replace the shims and the shim covers if rust is excessively attached.
• Eliminate rust on the pad retainers and the torque member. Replace them if rust is excessively attached.
INSPECTION AFTER INSTALLATION
PFIA0763J
JSFIA0493ZZ
JSFIA2918ZZ
JSFIA0491ZZ
REAR DISC BRAKE
BR-63
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
1. Check a drag of rear disc brake. If any drag is found, follow the procedure described below.
2. Remove brake pads. Refer to
BR-60, "BRAKE PAD : Removal and Installation"
.
3. Press the pistons. Refer to
BR-60, "BRAKE PAD : Removal and Installation"
.
4. Install brake pads. Refer to
BR-60, "BRAKE PAD : Removal and Installation"
.
5. Securely depress the brake pedal several times.
6. Check a drag of rear disc brake again. If any drag is found, disassemble the cylinder body and replace if
necessary. Refer to
BR-65, "BRAKE CALIPER ASSEMBLY : Disassembly and Assembly"
7. Burnish contact surfaces brake pads and disc rotor after refinishing or replacing brake pads, or if a soft
pedal occurs at very low mileage. Refer to
BR-18, "BRAKE PAD : Inspection and Adjustment"
BRAKE CALIPER ASSEMBLY
BRAKE CALIPER ASSEMBLY : Exploded View
INFOID:0000000012200307
REMOVAL
DISASSEMBLY
1.
Brake caliper assembly
: N·m (kg-m, ft-lb)
JPFIA0677GB
JSFIA0494GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст