Nissan Juke F15. Manual — part 101
BR-64
< REMOVAL AND INSTALLATION >
REAR DISC BRAKE
BRAKE CALIPER ASSEMBLY : Removal and Installation
INFOID:0000000012200308
REMOVAL
WARNING:
Since dust covering the rear brake has an affect on human body, the dust must be removed with a
dust collector. Never splatter the dust with an air blow gun.
CAUTION:
• Never spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe it
out immediately and wash with water if it gets on a protect surface. For brake component parts,
never wash them with water.
• Never depress the brake pedal while removing the brake hose. If this is not complied with, brake
fluid may splash.
• Never drop removed parts.
• If the brake fluid or grease adheres to the disc rotor, quickly wipe it off.
1. Remove tires with power tool.
2. Fix the disc rotor using wheel nuts.
3. Drain brake fluid. Refer to
.
4. Separate brake hose from caliper assembly. Refer to
BR-32, "REAR : Removal and Installation"
.
5. Remove torque member mounting bolts, and remove brake cali-
per assembly.
CAUTION:
Never drop brake pad and caliper assembly.
6. When removing disc rotor.
• 2WD: Refer to
RAX-7, "Removal and Installation"
.
• AWD: Refer to
RAX-16, "Removal and Installation"
.
INSTALLATION
WARNING:
Since dust covering the rear brake has an affect on human body, the dust must be removed with a
dust collector. Never splatter the dust with an air blow gun.
CAUTION:
• Never spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe it
out immediately and wash with water if it gets on a protect surface. For brake component parts,
never wash them with water.
• Never depress the brake pedal while removing the brake hose. If this is not complied with, brake
fluid may splash.
• If the brake fluid or grease adheres to the disc rotor, quickly wipe it off.
1. Install disc rotor.
• 2WD: Refer to
RAX-7, "Removal and Installation"
.
• AWD: Refer to
RAX-16, "Removal and Installation"
.
1.
Sliding pin bolt
2.
Bushing
3.
Cap
4.
Bleeder valve
5.
Cylinder body
6.
Piston seal
7.
Piston
8.
Piston boot
9.
Sliding pin boot
10. Torque member
: Apply rubber grease.
: Apply brake fluid.
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
: Always replace after every disassembly.
JSFIA0495ZZ
REAR DISC BRAKE
BR-65
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
2. Install the brake caliper assembly to the axle housing and
tighten the torque member mounting bolts to the specified
torque.
CAUTION:
Never spill or splash any grease and moisture on the brake
caliper assembly mounting face, threads, mounting bolts
and washers. Wipe out any grease and moisture.
3. Install brake hose. Refer to
BR-32, "REAR : Removal and Instal-
.
4. Perform the air bleeding. Refer to
5. Check a drag of rear disc brake. If any drag is found, refer to
BR-62, "BRAKE PAD : Inspection"
6. Install tires. Refer to
WT-39, "Removal and Installation"
.
7. Perform inspection after installation. Refer to
BR-67, "BRAKE CALIPER ASSEMBLY : Inspection"
.
BRAKE CALIPER ASSEMBLY : Disassembly and Assembly
INFOID:0000000012200309
DISASSEMBLY
NOTE:
Never remove the torque member, brake pad and pad retainers when disassembling and assembling the cyl-
inder body.
1. Remove the sliding pin bolt, and remove the cylinder body from the torque member. Refer to
"BRAKE PAD : Removal and Installation"
CAUTION:
Fix the brake pad at suitable tape so that the brake pad will not drop.
2. Remove sliding pin boots from torque member.
3. Remove bushing (1) from sliding pin bolt (2).
4. Place a wooden block as shown in the figure, and blow air from
union bolt mounting hole to remove pistons and piston boots.
CAUTION:
Never get fingers caught in the pistons.
JSFIA0495ZZ
JSFIA0496ZZ
MAA0272D
BR-66
< REMOVAL AND INSTALLATION >
REAR DISC BRAKE
5. Remove piston seal from cylinder body using seal pick tool.
CAUTION:
Be careful not to damage a cylinder inner wall.
6. Remove bleeder valve and cap.
7. Perform inspection after disassembly. Refer to
CALIPER ASSEMBLY : Inspection"
.
ASSEMBLY
1. Install bleeder valve and cap.
2. Apply rubber grease to piston seals (1), and install them to cylin-
der body.
CAUTION:
Never reuse piston seals.
3. Apply rubber grease to piston boots (1). Cover the piston (2) end
with piston boot, and then install cylinder side lip on piston boot
securely into a groove on cylinder body.
CAUTION:
Never reuse piston boots.
4. Apply new brake fluid to pistons (1). Push piston into cylinder
body by hand and push piston boot (2) piston-side lip into the
piston groove.
CAUTION:
Press the pistons evenly and vary the pressing point to pre-
vent cylinder inner wall from being rubbed.
JPFIA0738ZZ
JPFIA0039ZZ
JPFIA0739ZZ
JPFIA0034ZZ
REAR DISC BRAKE
BR-67
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
5. Apply rubber grease to mating faces (A) between sliding pin bolt
(1) and bushing (2), and install bushing to sliding pin.
6. Apply rubber grease to mating faces (A) between sliding pin bolt
(1) and sliding pin boot (2), and install sliding pin and sliding pin
boot to sliding torque member.
7. Install the cylinder body to tighten sliding pin bolts to the speci-
BR-59, "BRAKE PAD : Exploded View"
BRAKE CALIPER ASSEMBLY : Inspection
INFOID:0000000012200310
INSPECTION AFTER DISASSEMBLY
Check the following items and replace if necessary.
Cylinder Body
Check the inner wall of the cylinder for rust, wear, cracks or damage.
CAUTION:
Always clean with new brake fluid. Never clean with mineral oil such as gasoline and light oil.
Torque Member
Check the torque member for rust, wear, cracks or damage.
Pistons
Check the surface of the piston for rust, wear, cracks or damage.
CAUTION:
A piston sliding surface is plated. Never polish with sandpaper.
Sliding Pin, Sliding Pin Boot and Bushing
Check the sliding pins, sliding boots and bushing for rust, wear, cracks or damage.
INSPECTION AFTER INSTALLATION
1. Check a drag of rear disc brake. If any drag is found, follow the procedure described below.
2. Remove brake pads. Refer to
BR-60, "BRAKE PAD : Removal and Installation"
.
3. Press the pistons. Refer to
BR-60, "BRAKE PAD : Removal and Installation"
.
4. Install brake pads. Refer to
BR-60, "BRAKE PAD : Removal and Installation"
.
5. Securely depress the brake pedal several times.
6. Check a drag of rear disc brake again. If any drag is found, disassemble the cylinder body and replace if
necessary. Refer to
BR-65, "BRAKE CALIPER ASSEMBLY : Disassembly and Assembly"
.
7. Burnish contact surface between disc rotor and brake pads after refinishing or replacing disc rotor, or if a
soft pedal occurs at very low mileage. Refer to
BR-18, "DISC ROTOR : Inspection and Adjustment"
JSFIA0497ZZ
JSFIA0498ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст