Nissan Juke F15. Manual — part 784
FRONT DRIVE SHAFT BOOT
FAX-75
< REMOVAL AND INSTALLATION >
[TYPE 2]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
CAUTION:
• Since the drive shaft is assembled by press-fitting, use the tightening torque range for the wheel
hub lock nut.
• Be sure to use torque wrench to tighten the wheel hub lock nut. Never use a power tool.
• Never reuse wheel hub lock nut.
NOTE:
Wheel hub lock nut tightening torque does not over torque for avoiding axle noise, and does not less than
torque for avoiding looseness.
22. When installing a cotter pin (1) and adjusting cap (2), securely
bend the basal portion to prevent rattles.
CAUTION:
Never reuse cotter pin.
23. Install tires. Refer to
.
24. Perform inspection after installation. Refer to
.
Transaxle Side
• Install drive shaft to vehicle.
- Installation: Refer to
FAX-83, "2WD : Removal and Installation"
- Assembly: Refer to
FAX-87, "2WD : Disassembly and Assembly"
.
2WD : Inspection
INFOID:0000000012201556
INSPECTION AFTER INSTALLATION
1. Check wheel sensor harness for proper connection. Refer to
BRC-147, "FRONT WHEEL SENSOR :
.
2. Check the wheel alignment. Refer to
.
3. Adjust neutral position of steering angle sensor. Refer to
.
AWD
AWD : Exploded View
INFOID:0000000012201557
LEFT SIDE
JPDIF0295ZZ
JSDIA2093ZZ
FAX-76
< REMOVAL AND INSTALLATION >
[TYPE 2]
FRONT DRIVE SHAFT BOOT
RIGHT SIDE
AWD : Removal and Installation
INFOID:0000000012201558
REMOVAL
Wheel Side
1. Remove tires with power tool. Refer to
WT-39, "Removal and Installation"
.
2. Remove wheel sensor and sensor harness. Refer to
BRC-147, "FRONT WHEEL SENSOR : Exploded
.
3. Remove lock plate from strut assembly. Refer to
BR-25, "FRONT : Removal and Installation"
4. Remove caliper assembly. Hang caliper assembly not to interfere with work. Refer to
CALIPER ASSEMBLY : Removal and Installation"
.
CAUTION:
Never depress brake pedal while brake caliper is removed.
5. Remove disc rotor.
CAUTION:
1.
Circular clip
2.
Dust shield
3.
Housing assembly
4.
Boot band
5.
Boot
6.
Damper band
7.
Dynamic damper
8.
Circular clip
9.
Joint sub-assembly
: Wheel side
: Fill NISSAN Genuine grease or equivalent.
: Always replace after every disassembly.
1.
Joint sub-assembly
2.
Circular clip
3.
Boot band
4.
Boot
5.
Damper band
6.
Dynamic damper
7.
Housing assembly
: Wheel side
: Fill NISSAN Genuine grease or equivalent.
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
JSDIA2095GB
FRONT DRIVE SHAFT BOOT
FAX-77
< REMOVAL AND INSTALLATION >
[TYPE 2]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
• Put matching marks (A) on the wheel hub assembly and
the disc rotor before removing the disc rotor.
• Never drop disc rotor.
6. Remove cotter pin, and adjusting cap, and then loosen wheel hub lock nut with power tool.
7. Patch wheel hub lock nut with a piece of wood. Hammer the
wood to disengage wheel hub assembly from drive shaft.
NOTE:
Use suitable puller, if wheel hub assembly and drive shaft can-
not be separated even after performing the above procedure.
8. Remove wheel hub lock nut.
9. Remove strut assembly from steering knuckle. Refer to
FSU-9, "Removal and Installation"
.
10. Remove drive shaft from wheel hub assembly.
CAUTION:
• Never place drive shaft joint at an extreme angle. Also be careful not to overextend slide joint.
• Never allow drive shaft to hang down without support for joint sub-assembly, shaft and the other
parts.
11. Remove boot bands, and then remove boot from joint sub-assembly.
12. Screw drive shaft puller (A) (commercial service tool) into joint
sub-assembly screw part to a length of 30 mm (1.18 in) or more.
Support drive shaft with one hand and pull out joint sub-assem-
bly from shaft.
CAUTION:
• Align drive shaft puller and drive shaft and remove them
by pulling firmly and uniformly.
• If joint sub-assembly cannot be pulled out, try after
removing drive shaft from vehicle. Refer to
.
13. Remove circular clip (1) from shaft.
14. Remove boot from shaft.
Transaxle Side
• Remove boot after removing drive shaft.
JPDIG0066ZZ
JPDIG0070ZZ
JPDIF0258ZZ
JPDIF0007ZZ
FAX-78
< REMOVAL AND INSTALLATION >
[TYPE 2]
FRONT DRIVE SHAFT BOOT
FAX-97, "AWD : Removal and Installation"
.
- Disassembly: Refer to
FAX-101, "AWD : Disassembly and Assembly"
INSTALLATION
Wheel Side
1. Clean the old grease on joint sub-assembly with paper waste.
2. Fill serration slot joint sub-assembly (1) with NISSAN genuine
grease or equivalent until the serration slot and ball groove
become full to the brim.
CAUTION:
After applying grease, use a paper waste to wipe off old
grease that has oozed out.
3. Install boot and boot bands to shaft.
CAUTION:
• Wrap serration on shaft with tape to protect the boot from damage.
• Never reuse boot and boot band.
4. Remove the tape wrapped around the serration on shaft.
5. Position the circular clip (1) on groove at the shaft edge.
CAUTION:
Never reuse circular clip.
NOTE:
Drive joint inserter is recommended when installing circular clip.
6. Align both center axles of the shaft edge and joint sub-assembly. Then assemble shaft with joint sub-
assembly holding circular clip.
7. Install joint sub-assembly (1) to shaft using plastic hammer.
CAUTION:
• Check circular clip is properly positioned on groove of the
joint sub-assembly.
• Confirm that joint sub-assembly is correctly engaged
while rotating drive shaft.
8. Apply the specified amount of grease into the boot inside from large diameter side of boot.
JPDIF0008ZZ
JPDIF0007ZZ
JPDIF0011ZZ
Grease amount
: Refer to
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст