Nissan Juke F15. Manual — part 785
FRONT DRIVE SHAFT BOOT
FAX-79
< REMOVAL AND INSTALLATION >
[TYPE 2]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
9. Install the boot securely into grooves (indicated by “*” marks)
shown in the figure.
CAUTION:
If grease adheres to the boot mounting surface (indicated
by “*” marks) on the shaft or joint sub-assembly, boot may
be removed. Remove all grease from the boot mounting
surface.
10. To prevent the deformation of the boot, adjust the boot installation length (L) to the specified value shown
below by inserting the suitable tool into inside of the boot from the large diameter side of the boot and dis-
charging the inside air.
CAUTION:
• If the boot installation length exceeds the standard, it may cause breakage of the boot.
• Be careful not to touch the inside of the boot with a tip of tool.
11. Secure the large and small ends of the boot with boot bands
using the boot band crimping tool (A) [SST:KV40107300 ( —
)].
CAUTION:
• Never reuse boot band.
• Secure boot band so that dimension (M) meets the speci-
fication as shown in the figure.
12. Check that displacement does not occur when boot is rotated with the joint sub-assembly and shaft fixed.
CAUTION:
• Reinstall them using boot bands when boot installation positions become incorrect.
• Never reuse boot band.
13. Clean the matching surface of wheel hub lock nut and wheel hub assembly.
CAUTION:
Never apply lubricating oil to these matching surface.
JSDIA2261ZZ
L
: Refer to
.
JPDIF0012ZZ
Dimension (M)
: 2.0 – 3.0 mm (0.079 – 0.118 in)
DSF0047D
FAX-80
< REMOVAL AND INSTALLATION >
[TYPE 2]
FRONT DRIVE SHAFT BOOT
14. Clean the matching surface of drive shaft, wheel hub assembly.
And then apply paste [service parts (440037S000)] to surface
(A) of joint sub-assembly of drive shaft.
CAUTION:
Apply paste to cover entire flat surface of joint sub-assem-
bly of drive shaft.
15. Insert drive shaft to wheel hub assembly, and then temporarily tighten wheel hub lock nut.
CAUTION:
• Be sure to use torque wrench to tighten the wheel hub lock nut. Never use a power tool.
• Never reuse wheel hub lock nut.
16. Install strut assembly to steering knuckle. Refer to
.
17. Install disc rotor. Refer to
FAX-66, "Removal and Installation"
18. Install caliper assembly to steering knuckle. Refer to
BR-55, "BRAKE CALIPER ASSEMBLY : Removal
19. Install lock plate to strut assembly. Refer to
BR-25, "FRONT : Removal and Installation"
20. Install wheel sensor and sensor harness. Refer to
BRC-147, "FRONT WHEEL SENSOR : Exploded
.
21. Use the following torque range for tightening the wheel hub lock nut.
CAUTION:
• Since the drive shaft is assembled by press-fitting, use the tightening torque range for the wheel
hub lock nut.
• Be sure to use torque wrench to tighten the wheel hub lock nut. Never use a power tool.
• Never reuse wheel hub lock nut.
NOTE:
Wheel hub lock nut tightening torque does not over torque for avoiding axle noise, and does not less than
torque for avoiding looseness.
22. When installing a cotter pin (1) and adjusting cap (2), securely
bend the basal portion to prevent rattles.
CAUTION:
Never reuse cotter pin.
23. Install tires. Refer to
.
24. Perform inspection after installation. Refer to
Transaxle Side
• Install drive shaft to vehicle.
- Installation: Refer to
FAX-97, "AWD : Removal and Installation"
- Assembly: Refer to
FAX-101, "AWD : Disassembly and Assembly"
.
AWD : Inspection
INFOID:0000000012201559
INSPECTION AFTER INSTALLATION
Amount paste
: 1.0 – 3.0 g (0.04 – 0.10 oz)
JSDIA2844ZZ
: 180 – 185 N·m (18.4 – 18.8 kg-m, 133 – 136 ft-lb)
JPDIF0295ZZ
FRONT DRIVE SHAFT BOOT
FAX-81
< REMOVAL AND INSTALLATION >
[TYPE 2]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
1. Check wheel sensor harness for proper connection. Refer to
BRC-147, "FRONT WHEEL SENSOR :
.
2. Check the wheel alignment. Refer to
.
3. Adjust neutral position of steering angle sensor. Refer to
.
FAX-82
< REMOVAL AND INSTALLATION >
[TYPE 2]
FRONT DRIVE SHAFT
FRONT DRIVE SHAFT
2WD
2WD : Exploded View
INFOID:0000000012201560
LEFT SIDE
RIGHT SIDE
1.
Circular clip
2.
Dust shield
3.
Housing assembly
4.
Boot band
5.
Boot
6.
Damper band
7.
Dynamic damper
8.
Circular clip
9.
Joint sub-assembly
: Wheel side
: Fill NISSAN Genuine grease or equivalent.
: Always replace after every disassembly.
JSDIA2093ZZ
1.
Joint sub-assembly
2.
Circular clip
3.
Boot band
4.
Boot
5.
Damper band
6.
Dynamic damper
7.
Housing assembly
8.
Dust shield
9.
Support bearing
10. Snap ring
11. Plate
12. Support bearing bracket
JSDIA2094GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст