Nissan Juke F15. Manual — part 286
ELECTRIC CONTROLLED COUPLING OIL SEAL
DLN-149
< REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: RTVS]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
ELECTRIC CONTROLLED COUPLING OIL SEAL
Exploded View
INFOID:0000000012199509
Removal and Installation
INFOID:0000000012199510
REMOVAL
1. Remove rear drive shafts. Refer to
RAX-19, "Removal and Installation"
.
2. Remove electric controlled coupling oil seal from electric con-
trolled coupling, using the suitable oil seal remover.
CAUTION:
Never damage electric controlled coupling.
INSTALLATION
1. Using the drift (A) [SST: KV38109700 (
—
)], install elec-
tric controlled coupling oil seal to electric controlled coupling to
electric controlled coupling all the way until SST contact the end.
NOTE:
The use of SST satisfies the mounting dimensions.
CAUTION:
• Always use SST [KV38109700 (
—
)].
• Never reuse oil seal.
• When installing, never incline oil seal.
• Apply multi-purpose grease onto oil seal lips, and gear oil
onto the circumference of oil seal.
1.
Rear final drive assembly
2.
Electric controlled coupling oil seal
A.
Oil seal lip
: Always replace after every disassembly.
: Apply multi purpose grease
: Apply gear oil.
JSDIA2243ZZ
JSDIA2244ZZ
JSDIA2245ZZ
DLN-150
< REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: RTVS]
ELECTRIC CONTROLLED COUPLING OIL SEAL
2. Install rear drive shafts. Refer to
RAX-19, "Removal and Installation"
CAUTION:
Never damage electric controlled coupling oil seal.
REAR FINAL DRIVE ASSEMBLY
DLN-151
< UNIT REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: RTVS]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
UNIT REMOVAL AND INSTALLATION
REAR FINAL DRIVE ASSEMBLY
Exploded View
INFOID:0000000012199511
Removal and Installation
INFOID:0000000012199512
REMOVAL
1. Remove rear drive shaft. Refer to
RAX-19, "Removal and Installation"
2. Disconnect sub-harness connector (1).
3. Remove propeller shaft assembly. Refer to
4. Support rear final drive assembly with a suitable jack.
1.
Final drive mounting bracket
2.
Washer
3.
Rear final drive assembly
: Vehicle front
: Always replace after every disassembly
: N·m (kg-m, ft-lb)
: Apply multi purpose grease
: Apply gear oil.
JSDIA2134GB
JSDIA2135ZZ
DLN-152
< UNIT REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: RTVS]
REAR FINAL DRIVE ASSEMBLY
5. Remove rear final drive mounting bolt (
) at rear suspension
member.
6. Remove final drive mounting bolts and nuts (
) with power tool,
and then remove rear final drive assembly from final drive
mounting bracket.
CAUTION:
Secure final drive assembly to a suitable jack while remov-
ing it.
7. Remove rear final drive breather hose.
8. Remove fuel tank. Refer to
FL-23, "AWD : Removal and Installa-
9. Remove final drive mounting bracket.
INSTALLATION
Note the following, and install in the reverse order of removal.
• If remove breather hose, install breather hose as following.
- Insert breather hose (1) of final drive side to breather tube (2) until
hose end reaches the tube bent R portion.
- Install the breather to breather hose until hose end reaches the
breather.
- Install hose clamp (1) until dimension (A) shown as follows.
CAUTION:
• Never reuse hose clamps.
• Install the hose clamps, with the tab facing vehicle rear.
JSDIA2136ZZ
JSDIA2137ZZ
(3): Breather
JSDIA2468ZZ
Dimension A
: 5 mm (0.20 in)
JSDIA2531ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст