Nissan Juke F15. Manual — part 287
REAR FINAL DRIVE ASSEMBLY
DLN-153
< UNIT REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: RTVS]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
- Install breather assembly (1) to final drive as shown in the figure.
- Install breather hose with paint mark (A) facing vehicle rear.
• When installing rear drive shaft, never damage electric controlled
coupling oil seal.
• When oil leaks while removing final drive assembly, check oil level
after the installation. Refer to
• When replacing rear final drive assembly or electric controlled cou-
pling, perform writing unit characteristics after installing rear final
drive assembly to the vehicle. Refer to
CAUTION:
Always writing unit characteristics of both side electric controlled couplings.
(A): Paint mark
: Vehicle front
JSDIA2138ZZ
DLN-154
< UNIT DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: RTVS]
ELECTRIC CONTROLLED COUPLING
UNIT DISASSEMBLY AND ASSEMBLY
ELECTRIC CONTROLLED COUPLING
Exploded View
INFOID:0000000012199513
1.
Filler plug
2.
Gasket
3.
Drain plug
4.
Breather tube
5.
Hose clamp
6.
Breather hose
7.
Breather
8.
Band clip
9.
Sub-harness
10. Rear cover
11. Center stem
12. Side bearing (right)
13. Side bearing adjusting shim (right)
14. Side oil seal (right)
15. Connector clip
16. Electric controlled coupling (right)
17. Electric controlled coupling oil seal
18. Reamer bolt
19. Drive pinion
20. Drive pinion adjusting shim
21. Pinion bearing (rear)
22. Collapsible spacer
23. Breather
24. Gear carrier
25. Carrier bracket (right)
26. Pinion bearing (front)
27. Front oil seal
28. Companion flange
29. Drive pinion lock nut
30. Carrier bracket (left)
31. Drive gear
32. Side bearing (left)
33. Side bearing adjusting shim (left)
34. Side oil seal (left)
35. Electric controlled coupling (left)
A.
Oil seal lip
B.
Gear carrier mounting face
: Always replace after every disassembly.
: Select with proper thickness.
: N·m (kg-m, ft-lb)
: Apply multi purpose grease
: Apply gear oil.
JSDIA2246GB
ELECTRIC CONTROLLED COUPLING
DLN-155
< UNIT DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: RTVS]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
Disassembly
INFOID:0000000012199514
1. Disconnect electric controlled coupling connector (1) from sub-
harness (2).
2. Remove electric controlled coupling connector from final drive
assembly.
3. Remove electric controlled coupling from final drive assembly.
CAUTION:
Never damage side oil seal.
4. Remove sub-harness from final drive assembly.
CAUTION:
Remove sub-harness only when necessary.
5. Remove electric controlled coupling oil seal from electric con-
trolled coupling, using the suitable oil seal remover.
CAUTION:
Never damage electric controlled coupling.
: Apply anti-corrosive oil.
: Apply Genuine Silicone RTV or equivalent. Refer to
GI-22, "Recommended Chemical Products and Sealants"
.
JSDIA2238ZZ
JSDIA2239ZZ
JSDIA2474ZZ
JSDIA2571ZZ
DLN-156
< UNIT DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: RTVS]
ELECTRIC CONTROLLED COUPLING
Assembly
INFOID:0000000012199515
1. Using the drift (A) [SST: KV38109700 (
—
)], install elec-
tric controlled coupling oil seal to electric controlled coupling to
electric controlled coupling all the way until SST contact the end.
NOTE:
The use of SST satisfies the mounting dimensions.
CAUTION:
• Always use SST [KV38109700 (
—
)].
• Never reuse oil seal.
• When installing, never incline oil seal.
• Apply multi-purpose grease onto oil seal lips, and gear oil
onto the circumference of oil seal.
2. If remove sub–harness, replace band clip to sub-harness, and
then install sub–harness to rear final drive assembly.
CAUTION:
• Never reuse band clip.
• Check original mounting dimensions to install clip to the original position.
• Pin (A) of sub–harness connector clip must be function-
ing certainly as baffle pin.
• Check the area around the rotating object to see that there
is no interference.
3. Apply liquid gasket (1) to mating surface of coupling cover.
• Use Genuine Silicone RTV or equivalent. Refer to
"Recommended Chemical Products and Sealants"
.
CAUTION:
• Remove old gasket adhering to the mounting surfaces.
Also remove any moisture, oil, or foreign material adher-
ing to the mounting surfaces.
• Overlap both ends of the bead for at least 3 mm (0.12 in).
• Apply liquid gasket to grommet as well.
• The width of sealant bend is approximately 3 mm (0.012
in).
• Never allow liquid gasket to contact the unit characteris-
tics (A or B) of the coupling cover.
JSDIA2301ZZ
JSDIA2525ZZ
JSDIA2241ZZ
JSDIA2572ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст