Nissan Juke F15. Manual — part 1284
TM-326
< REMOVAL AND INSTALLATION >
[CVT: RE0F10B]
TRANSMISSION RANGE SWITCH
TRANSMISSION RANGE SWITCH
Exploded View
INFOID:0000000012201021
Removal and Installation
INFOID:0000000012201022
REMOVAL
1. Remove battery. Refer to
PG-105, "Removal and Installation"
.
2. Remove transmission range switch connector.
3. Remove control cable. Refer to
TM-319, "Removal and Installation"
.
4. Remove transmission range switch from transaxle assembly.
INSTALLATION
Install in the reverse order of removal.
Inspection and Adjustment
INFOID:0000000012201023
ADJUSTMENT OF TRANSMISSION RANGE SWITCH
1. Move selector lever to “N” position.
2. Remove control cable from manual lever.
1.
Transmission range switch
2.
Transaxle assembly
: N·m (kg-m, in-lb)
JSDIA2397GB
TRANSMISSION RANGE SWITCH
TM-327
< REMOVAL AND INSTALLATION >
[CVT: RE0F10B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
3. Loosen mounting bolts (
) of transmission range switch. Insert
a pin (
φ4 mm) into the adjusting holes (A) on both transmission
range switch and manual lever for adjusting the position.
4. Tighten mounting bolts of transmission range switch.
5. Connect control cable on manual lever. Refer to
.
ADJUSTMENT AFTER INSTALLATION
Adjust the CVT positions after installing the CVT shift selector. Refer to
TM-233, "Inspection and Adjustment"
.
INSPECTION AFTER INSTALLAION
Check the CVT positions after adjusting the CVT positions. Refer to
TM-233, "Inspection and Adjustment"
JSDIA2398ZZ
TM-328
< REMOVAL AND INSTALLATION >
[CVT: RE0F10B]
TCM
TCM
Exploded View
INFOID:0000000012201024
Removal and Installation
INFOID:0000000012201025
CAUTION:
• Never impact on TCM when removing or installing TCM.
• When replacing TCM, note the “CVTF DETERIORATION DATE” value displayed on CONSULT “CON-
FORM CVTF DETERIORTN” in MAINTENANCE BOOKLET, before start the operation.
• When replacing TCM and transaxle assembly simultaneously, replace transaxle assembly first and
then replace TCM. Refer to
TM-347, "Removal and Installation"
• Before replacing TCM, perform “ADDITIONAL SERVICE WHEN REPLACING TCM”. Refer to
REMOVAL
1. Remove the battery. Refer to
PG-105, "Removal and Installation"
.
2. Remove air duct (inlet) and air cleaner case. Refer to
EM-27, "Removal and Installation"
.
3. Disconnect the TCM connector.
4. Remove the TCM.
5. Remove the bracket.
INSTALLATION
Installation is the reverse order of removal.
Adjustment
INFOID:0000000012201026
ADJUSTMENT AFTER INSTALLATION
Perform "ADDITIONAL SERVICE WHEN REPLACING TCM". Refer to
1.
Bracket
2.
TCM
:Vehicle front
: N·m (kg-m, in-lb)
JSDIA7186GB
AIR BREATHER HOSE
TM-329
< REMOVAL AND INSTALLATION >
[CVT: RE0F10B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
AIR BREATHER HOSE
Removal and Installation
INFOID:0000000012201027
REMOVAL
1. Remove air cleaner case. Refer to
EM-27, "Removal and Installation"
.
2. Remove clip (A) from bracket.
3. Remove air breather hose (1) from transaxle assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• Never bend the air breather hose to prevent damage to the hose.
• Install air breather hose (1) to transaxle tube (A) all the way to
the curve of the tube.
• Install air breather hose to transaxle tube so that the paint
mark (B) is facing upward.
• Securely install the clip (A) to the bracket.
JSDIA2454ZZ
JSDIA2399ZZ
JSDIA2458ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст