Nissan Juke F15. Manual — part 1285
TM-330
< REMOVAL AND INSTALLATION >
[CVT: RE0F10B]
CONTROL VALVE
CONTROL VALVE
Exploded View
INFOID:0000000012201028
Removal and Installation
INFOID:0000000012201029
REMOVAL
1. Disconnect battery cable from negative terminal. Refer to
.
1.
Transaxle assembly
2.
Control valve
3.
Bracket
4.
O-ring
5.
Oil strainer assembly
6.
Magnet
7.
Drain plug gasket
8.
Drain plug
9.
Oil pan mounting bolt
10.
Oil pan
11. Oil pan gasket
12. Lock nut
13.
Washer
14. Manual plate
15. Collar
16.
Lip seal
17. Snap ring
18. Terminal cord assembly
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
: Apply CVT fluid
JSDIA2656GB
CONTROL VALVE
TM-331
< REMOVAL AND INSTALLATION >
[CVT: RE0F10B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
2. Remove drain plug from oil pan and then drain the CVT fluid.
3. Remove drain plug gasket.
4. Disconnect the CVT unit connector. Refer to
TM-150, "Removal and Installation Procedure for CVT Unit
5. Remove the snap ring (1) from the CVT unit connector (A).
6. Press the CVT unit connector (A) into the transaxle case.
CAUTION:
Never damage the CVT unit connector.
NOTE:
Clean around the connector to prevent foreign materials from
entering into the transaxle case.
7. Remove the oil pan mounting bolts, and then remove the oil pan and oil pan gasket.
8. Remove the magnets from the oil pan.
9. Remove the lock nut (1) and washer (2), and then remove the
manual plate (3).
10. Remove the collar (4) from the manual shaft (A).
CAUTION:
Never drop the collar.
11. Disconnect the control valve connectors (A) and (B).
JPDIA0654ZZ
JPDIA0720ZZ
: Vehicle front
JPDIA0655ZZ
: Clip
: Vehicle front
JPDIA0656ZZ
TM-332
< REMOVAL AND INSTALLATION >
[CVT: RE0F10B]
CONTROL VALVE
12. Remove the oil strainer assembly mounting bolts (A) and (B),
and then remove the oil strainer assembly (1).
13. Remove O-ring from oil strainer assembly.
14. Remove the bracket (1).
15. Remove the control valve mounting bolts (A) and (B), and then
remove the control valve from the transaxle case.
CAUTION:
Never drop the control valve, ratio control valve and manual
shaft.
16. Remove terminal cord assembly (1) from the transaxle case
inside.
17. Remove the lip seal (1) from the transaxle case.
: Vehicle front
JPDIA0657ZZ
: Bolt
: Vehicle front
JPDIA0658ZZ
: Vehicle front
JPDIA0659ZZ
JSDIA2634ZZ
: Vehicle front
JPDIA0661ZZ
CONTROL VALVE
TM-333
< REMOVAL AND INSTALLATION >
[CVT: RE0F10B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
INSTALLATION
1. Install the lip seal (1) to the transaxle case.
2. Install terminal cord assembly (1) to the transaxle case.
CAUTION:
Connect the CVT unit connector with the stopper facing up,
and then press in until it clicks.
3. Press in the ratio control valve (B) in the (
) direction, and then
fix the linkage in the position shown in the figure with the linkage
fixing pin (A) from the back of control valve through the hole for
fixing.
4. Check that one end of linkage engages with the step motor end
(C) and that the linkage is in the direction shown in the figure.
5. Install the control valve to the transaxle case.
CAUTION:
• Never drop the linkage fixing pin. If it is dropped, repeat
the installation procedure from step 3.
• Never pinch the harness into between the control valve
and the transaxle case.
• Never drop the control valve, ratio control valve and man-
ual shaft.
: Vehicle front
JPDIA0661ZZ
JSDIA2634ZZ
JPDIA0663ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст