Nissan Juke F15. Manual — part 1155
SPIRAL CABLE
SR-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
• The spiral cable may snap during steering operation if the
cable is installed in an improper position.
The neutral position is set as per the following.
• Carefully turn the spiral cable clockwise to the end position.
Then turn it counterclockwise (about 2 and a half turns) and
stop turning at the mark (B) when the stopper insertion holes
are in the same position.
• The service part is installed in the neutral position by the
stopper and can be set without adjusting after the stopper is
removed.
• Never over turn the spiral cable or go beyond the number of
turns required. (This causes the cable to snap)
• Adjust the spiral cable locating pin (A) to the steering wheel
locating pin hole (C).
• Fix the driver air bag module harnesses to the harness fixing
hook (A).
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to
.
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
JMHIA0879ZZ
JMHIA1608ZZ
SR-18
< REMOVAL AND INSTALLATION >
PASSENGER AIR BAG MODULE
PASSENGER AIR BAG MODULE
Exploded View
INFOID:0000000012199973
Removal and Installation
INFOID:0000000012199974
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Always work from the side of air bag module. Never work in front of it.
• Never use the air tools or the electric tools for servicing.
REMOVAL
1. Remove instrument side finisher RH, glove box lid, and glove box assembly. Refer to
.
1.
Passenger air bag module
2.
Instrument panel assembly
: Pawl
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
JMHIA1657GB
PASSENGER AIR BAG MODULE
SR-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
2. Disconnect passenger air bag module harness connector (A)
from passenger air bag module.
3. Remove passenger air bag module fixing bolts (B).
4. Put a hand to back of instrument panel (glove box opening), dis-
engage connections of the passenger air bag module pawls
from the inside of the vehicle toward the outside, and remove.
CAUTION:
• Never insert a remover tool between passenger air bag
module and instrument panel assembly. Doing so may
cause damage.
• Wear gloves.
CAUTION:
• Always place the passenger air bag module with pad side fac-
ing upward.
• Never impact the passenger air bag module.
• Replace the passenger air bag module if it has been dropped
or sustained an impact.
• Never insert any foreign objects (screwdriver, etc.) into the passenger air bag module.
• Never disassemble the passenger air bag module.
• Never expose the passenger air bag module to temperatures exceeding 90
°C (194 °F).
• Never allow oil, grease, detergent, or water to come in contact with the passenger air bag module.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Never use the old fixing bolts after removal, replace with the new bolts.
• Never damage the harness while installing.
JMHIA1658ZZ
: Pawl
JMHIA1659ZZ
: Upward
JMHIA1613ZZ
JMHIA0009ZZ
SR-20
< REMOVAL AND INSTALLATION >
PASSENGER AIR BAG MODULE
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to
or
.
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст