Nissan Juke F15. Manual — part 1154
DRIVER AIR BAG MODULE
SR-13
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Always work from the side of air bag module. Never work in front of it.
• Never use the air tools or electric tools for servicing.
REMOVAL
1. Remove side lid (LH and RH).
Insert flat-bladed screwdriver between side lid and steering
wheel to disengage pawls as shown in the figure.
2. Remove TORX bolts (LH and RH) from the steering wheel lower side.
3. Pull out driver air bag module.
4. Disconnect spiral cable harness connector (A).
5. Disconnect driver air bag harness connector (B).
CAUTION:
• For installing/removing the driver air bag module harness
connector, insert thin screwdriver wrapped in tape into
notch, lift lock and remove the connector.
• Install the connector with lock raised, and push lock into
the connector.
• After installing the connector, check that the lock is
pushed securely into it.
6. Remove driver air bag module.
CAUTION:
• Always place the driver air bag module with pad side facing
upward.
: Pawl
JMHIA1605ZZ
JMHIA1606ZZ
PHIA0953J
: Upward
JMHIA1607ZZ
SR-14
< REMOVAL AND INSTALLATION >
DRIVER AIR BAG MODULE
• Never impact the driver air bag module.
• Replace the driver air bag module if it has been dropped or
sustained an impact.
• Never insert any foreign objects (screwdriver, etc.) into the driver air bag module.
• Never disassemble the driver air bag module.
• Never expose the driver air bag module to temperatures exceeding 90
°C (194 °F).
• Never allow oil, grease, detergent, or water to come in contact with the driver air bag module.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Never use the old TORX bolts after removal, replace with the new TORX bolts.
• Fix the driver air bag module harnesses to the harness fixing
hook (A).
• Never damage the harness while installing.
• Tighten the TORX bolts after completely adjusting the centers of fixing holes on the driver air bag
module side and the steering wheel side. If the holes are misaligned, the bolt threads are damaged
and the module is not installed securely.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to
or
.
• After the work is complete, check that no system malfunction is detected by air bag warning lamp.
JMHIA0009ZZ
JMHIA1608ZZ
SPIRAL CABLE
SR-15
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
SPIRAL CABLE
Exploded View
INFOID:0000000012199971
Removal and Installation
INFOID:0000000012199972
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Never use the air tools or electric tools for servicing.
1.
Steering column upper cover
2.
Steering column assembly
3.
Steering column lower cover
4.
Side lid LH
5.
TORX bolt
6.
Driver air bag module
7.
TORX bolt
8.
Side lid RH
9.
Steering wheel
10. Spiral cable
11. Steering angle sensor
12. Combination switch
13. Steering switch
: Pawl
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
JMHIA1655GB
SR-16
< REMOVAL AND INSTALLATION >
SPIRAL CABLE
REMOVAL
1. Remove driver air bag module. Refer to
SR-12, "Removal and Installation"
.
2. Remove steering wheel. Refer to
ST-9, "Removal and Installation"
3. Remove steering column upper cover and steering column lower cover. Refer to
.
4. Disconnect the spiral cable body side harness connectors (A),
(B) and steering angle sensor harness connectors (C).
NOTE:
Disconnect the spiral cable body side harness connector (B)
after removing the spiral cable (A).
5. Remove the spiral cable fixing screws.
6. Remove the spiral cable fixing pawls with remover tool (A).
CAUTION:
Remove pawls slowly so that they are not damaged.
7. Remove the steering angle sensor. Refer to
BRC-156, "Removal and Installation"
.
CAUTION:
• Never impact the spiral cable.
• Replace the spiral cable if it is dropped or sustains an impact.
• Never disassemble the spiral cable.
• Never apply lubricant to the spiral cable.
• Never allow oil, grease, detergent, or water to come in contact with the spiral cable.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
JMHIA1656ZZ
: Pawl
JMHIA1610ZZ
JMHIA0009ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст