Nissan Juke F15. Manual — part 272
AWD MODE SWITCH
DLN-93
< REMOVAL AND INSTALLATION >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
AWD MODE SWITCH
Removal and Installation
INFOID:0000000012199461
REMOVAL
1. Remove instrument lower panel. Refer to
.
2. Remove AWD mode switch.
INSTALLATION
Install in the reverse order of removal.
DLN-94
< UNIT REMOVAL AND INSTALLATION >
[TRANSFER: TY21B]
TRANSFER ASSEMBLY
UNIT REMOVAL AND INSTALLATION
TRANSFER ASSEMBLY
Exploded View
INFOID:0000000012199462
Removal and Installation
INFOID:0000000012199463
REMOVAL
1. Separate the propeller shaft from transfer. Then suspend it by wire, etc. Refer to
.
CAUTION:
Constant velocity joint must be handled with care.
2. Remove right side drive shaft. Refer to
FAX-97, "AWD : Removal and Installation"
(Except for NISMO
RS),
FAX-45, "AWD : Removal and Installation"
(For NISMO RS).
3. Remove catalytic converter bracket (Except for NISMO RS) or catalyst convertor support bracket (upper)
(For NISMO RS).
4. Remove heat insulator (1).
1.
Transfer assembly
2.
Transfer gusset
3.
Heat insulator
: Vehicle front
: N·m (kg-m, ft-lb)
JSDIA2083GB
JSDIA2311ZZ
TRANSFER ASSEMBLY
DLN-95
< UNIT REMOVAL AND INSTALLATION >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
5. Remove transfer gusset (1).
6. Remove catalytic converter adapter bracket (Except for NISMO
RS) or catalyst convertor support bracket (lower) (For NISMO
(Except for
NISMO RS),
(For NISMO RS).
7. Remove rear torque rod and rear torque rod bracket. Refer to
EM-221, "AWD : Removal and Installation"
(Except for NISMO
EM-68, "AWD : Removal and Installation"
8. Remove bolts fixing transaxle assembly and transfer assembly.
9. Remove transfer assembly from the vehicle.
CAUTION:
• Never damage ring gear shaft.
• Be careful when removing transfer assembly form the
vehicle because it is heavy.
INSTALLATION
Note the following, and install in the reverse order of removal.
• When installing the transfer assembly to the transaxle assembly,
install the mounting bolts following the standard below.
CAUTION:
• When installing transfer assembly to transaxle assembly,
replace differential side oil seal (Converter housing side) of
transaxle. Refer to
TM-340, "Removal and Installation"
(RE0F10B),
TM-566, "Removal and Installation"
(RE0F10D).
• Never damage differential side oil seal (Converter housing
side) of transaxle.
• When installing heat insulator (1), tighten the mounting bolts and
nut in numerical order.
• Perform inspection after installation. Refer to
Inspection
INFOID:0000000012199464
INSPECTION AFTER INSTALLATION
Check oil level and check for oil leakage. Refer to
JSDIA2084ZZ
: Vehicle front
JSDIA2085ZZ
Bolt symbol
A
B
Installation direction
Transfer
⇒ Transaxle
Transaxle
⇒ Transfer
JSDIA2086ZZ
Temporary tightening
: 1
→ 2 → 3
Final tightening
(Specified torque)
: 4
→ 5 → 6
JSDIA2515GB
DLN-96
< UNIT DISASSEMBLY AND ASSEMBLY >
[TRANSFER: TY21B]
RING GEAR SHAFT
UNIT DISASSEMBLY AND ASSEMBLY
RING GEAR SHAFT
Exploded View
INFOID:0000000012199465
1.
Pinion lock nut
2.
Companion flange
3.
Drive pinion oil seal
4.
Pinion bearing (rear)
5.
Transfer case
6.
Gasket
7.
Filler plug
8.
Collapsible spacer
9.
Drive pinion adjusting shim
10. Pinion bearing (front)
11. Drive pinion
12. Ring gear
13. Ring gear shaft
14. Ring gear bearing (right)
15. Ring gear bearing adjusting shim
(right)
16. Spacer (right)
17. Transfer case oil seal (right)
18. Drive shaft oil seal
19. Transfer cover
20. Oil defense
21. Ring gear bearing (left)
22. Ring gear bearing adjusting shim
(left)
23. Spacer (left)
24. Transfer case oil seal (left)
25. Drain plug
26. Dowel pin
A.
Oil seal lip
B.
Transfer case mounting face
: Always replace after every disassembly.
: Select with proper thickness.
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
: Apply gear oil.
: Apply multi purpose grease
JSDIA2491GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст