Nissan Juke F15. Manual — part 273
RING GEAR SHAFT
DLN-97
< UNIT DISASSEMBLY AND ASSEMBLY >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
Disassembly
INFOID:0000000012199466
1. Remove transfer cover. Refer to
.
2. Remove transfer case oil seal (right and left).
3. Remove ring gear shaft assembly from transfer case. If ring gear shaft cannot be removed, remove as fol-
lows.
CAUTION:
Never damage transfer case.
• Set the drifts (A and B) to right and left spacers individually.
Compress ring gear shaft assembly with ring gear bearing to
remove ring gear shaft assembly from transfer case.
CAUTION:
• The drift shall be placed on the center of the spacers.
• The pressure shall be as low as to remove ring gear
shaft assembly from transfer case. The maximum pres-
sure shall be 10 kN (1 ton, 1.0 Imp ton).
• If the adjusting shims and spacers are installed by tap-
ping, the transfer case may be damaged. Avoid tapping.
4. Remove spacer (right and left) from ring gear shaft assembly.
5. Remove ring gear bearing adjusting shim (right and left) from ring gear shaft assembly.
6. Remove outer races of ring gear bearing (right and left) from ring gear shaft assembly.
7. Remove inner race of ring gear bearing (right) from ring gear
shaft with the drift (A) and the replacer (B).
8. Remove inner race of ring gear bearing (left) from ring gear shaft
with the replacer (A) (Commercial service tool).
9. Remove the ring gear mounting bolts.
: Apply anti-corrosive oil.
: Apply Genuine Silicone RTV or equivalent. Refer to
GI-22, "Recommended Chemical Products and Sealants"
.
A
: Drift (Commercial service tool)
B
: Drift (Commercial service tool)
A
: Drift [SST: ST33200000 (J-26082)]
B
: Replacer (Commercial service tool)
JSDIA1106ZZ
JSDIA2165ZZ
JSDIA2166ZZ
DLN-98
< UNIT DISASSEMBLY AND ASSEMBLY >
[TRANSFER: TY21B]
RING GEAR SHAFT
10. Lightly tap ring gear with a plastic hammer to remove ring gear
from ring gear shaft.
11. Remove drive shaft oil seal from the ring gear shaft with the
puller (A) [SST: KV381054S0 (J-34286)].
12. Perform inspection after disassembly. Refer to
Assembly
INFOID:0000000012199467
1. Select ring gear bearing adjusting shim (right and left). Refer to
2. Using the drift (A) [SST: ST33230000 (J-25805-01)], install drive
shaft oil seal (1) within the dimension (L) shown as follows.
CAUTION:
• Never reuse the oil seal.
• When installing, never incline oil seal.
• Apply multi-purpose grease to oil seal lip, and gear oil
onto the circumference.
3. Install the ring gear to ring gear shaft.
4. Install the inner race of ring gear bearing (left) to ring gear shaft
with the drift (A) (Commercial service tool).
CAUTION:
• Never reuse the ring gear bearing.
• Apply gear oil to ring gear bearing.
SDIA1807J
JPDIE0032ZZ
L
: 0 – 0.6 mm (0 – 0.024 in)
JSDIA2492ZZ
JSDIA1055ZZ
RING GEAR SHAFT
DLN-99
< UNIT DISASSEMBLY AND ASSEMBLY >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
5. Install the inner race of ring gear bearing (right) to ring gear shaft
with the drift (A) (Commercial service tool).
CAUTION:
• Never reuse the ring gear bearing.
• Apply gear oil to ring gear bearing.
6. Install outer races of ring gear bearing (right and left) to ring gear
shaft assembly.
CAUTION:
• Never reuse the ring gear bearing.
• Apply gear oil to ring gear bearing.
7. Install selected ring gear bearing adjusting shim (right and left)
to ring gear shaft assembly.
8. Install spacer (right and left) to ring gear shaft assembly.
9. Set the drifts (A and B) to right and left spacers individually.
Compress ring gear shaft assembly with ring gear bearing to
install ring gear shaft assembly to transfer case.
CAUTION:
• The drift shall be placed on the center of the spacers.
• The pressure shall be as low as to install ring gear shaft
assembly into transfer case. The maximum pressure shall
be 10 kN (1 ton, 1.0 Imp ton).
• If the adjusting shims and spacers are installed by tap-
ping, the transfer case may be damaged. Avoid tapping.
10. Install transfer cover to check and adjust each part. Refer to
CAUTION:
Never apply liquid gasket.
11. Check backlash, tooth contact, and total preload. Refer to
.
CAUTION:
Measure the total preload without the transfer case oil seal.
12. Reinstall transfer cover for applying liquid gasket. Refer to
13. Install the transfer case oil seal (left and right). Refer to
Adjustment
INFOID:0000000012199468
Adjusting shim selection
A
: Drift (Commercial service tool)
B
: Drift (Commercial service tool)
JSDIA1056ZZ
JSDIA1106ZZ
DLN-100
< UNIT DISASSEMBLY AND ASSEMBLY >
[TRANSFER: TY21B]
RING GEAR SHAFT
Measurement point
Ring gear bearing adjusting shim (left)
1. Measure the dimensions of each measuring point with the following procedure:
Dimension “A” measurement
• Measure dimension (A) of transfer case with a pair of vernier
calipers. Refer to “Measuring point”.
CAUTION:
Never damage transfer case.
Dimension “X” measurement
JSDIA2493ZZ
JSDIA2170ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст