Nissan Juke F15. Manual — part 265
P1832 TCS OPERATION SIGNAL
DLN-65
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
P1832 TCS OPERATION SIGNAL
DTC Logic
INFOID:0000000012199411
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION
With CONSULT
1. Start the engine and drive at 30 km/h (19 MPH) or more for approximately 3 minute.
2. Stop the vehicle.
3. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P1832” detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012199412
1.
PERFORM ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “ABS”.
Is any DTC detected?
YES
>> Perform trouble diagnosis for detected DTC. Refer to
NO
>> GO TO 2.
2.
ERASE SELF-DIAGNOSTIC RESULT
With CONSULT
1. Erase self-diagnostic results for “ALL MODE AWD/4WD”.
2. Start the engine and drive at 30 km/h (19 MPH) or more for approximately 3 minute.
3. Stop the vehicle.
4. Check that ABS warning lamp turns OFF.
Does ABS warning lamp turn OFF?
YES
>> GO TO 3.
NO
>> Refer to
BRC-136, "Component Function Check"
.
3.
CHECK TERMINALS AND HARNESS CONNECTORS
Check AWD control module pin terminals for damage or loose connection with harness connector.
Is inspection result normal?
YES
>> After turning the ignition switch OFF, perform DTC confirmation procedure again. If DTC “P1832”
is detected, Replace AWD control module. Refer to
DLN-91, "Removal and Installation"
NO
>> Repair or replace error-detected parts.
DTC
Display item
Malfunction detected condition
Possible cause
P1832
TCS OP SIG
Malfunction is detected in TCS operation
signal that is output from ABS actuator
and electric unit (control unit) through
CAN communication.
• ABS actuator and electric unit (control
unit)
• AWD control module
• CAN communication line
DLN-66
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
P183B SOLENOID POWER SUPPLY
P183B SOLENOID POWER SUPPLY
DTC Logic
INFOID:0000000012199413
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION
With CONSULT
1. Turn the ignition switch OFF to ON.
2. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P183B” detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012199414
1.
CHECK AWD SOLENOID POWER SUPPLY (1)
1. Turn the ignition switch OFF.
2. Disconnect AWD control module harness connector.
3. Check the voltage between AWD control module harness connector and ground.
4. Turn the ignition switch OFF to ON.
CAUTION:
Never start the engine.
5. Check the voltage between AWD control module harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK AWD SOLENOID POWER SUPPLY (2)
1. Turn the ignition switch OFF.
2. Check the 10A fuse (#12).
DTC
Display item
Malfunction detected condition
Possible cause
P183B
SOL POWER SUPPLY
When AWD solenoid power supply volt-
age is lower or higher than normal.
• Malfunction of AWD solenoid power
supply circuit
• Malfunction of AWD control module
• Malfunction of AWD control module
power supply circuit (open or short)
• Battery
AWD control module
—
Voltage
Connector
Terminal
B47
12
Ground
11 – 13 V
AWD control module
—
Voltage
Connector
Terminal
B47
12
Ground
11 – 13 V
P183B SOLENOID POWER SUPPLY
DLN-67
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
3. Check the harness for open or short between AWD control module harness connector No.12 and the 10A
fuse (#12).
Is the inspection result normal?
YES
>> Perform the trouble the diagnosis for power supply circuit. Refer to
.
NO
>> Repair or replace error-detected parts.
3.
CHECK AWD CONTROL MODULE POWER SUPPLY (1)
1. Turn the ignition switch OFF.
2. Check the voltage between AWD control module harness connector and ground.
3. Turn the ignition switch ON.
CAUTION:
Never start the engine.
4. Check the voltage between AWD control module harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 4.
4.
CHECK AWD CONTROL MODULE POWER SUPPLY (2)
1. Turn the ignition switch OFF.
2. Check the 10A fuse (#3).
3. Check the harness for open or short between AWD control module harness connector No.3 terminal and
10A fuse (#3).
Is the inspection result normal?
YES
>> Perform the trouble diagnosis for ignition power supply circuit. Refer to
NO
>> Repair or replace error-detected parts.
5.
CHECK AWD SOLENOID GROUND
Check the continuity between AWD control module harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace the error-detected parts.
6.
CHECK TERMINALS AND HARNESS CONNECTORS
1. Check AWD control module pin terminals for damage or loose connection with harness connector.
2. Check AWD solenoid pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES
>> Replace AWD control module. Refer to
DLN-91, "Removal and Installation"
.
NO
>> Repair or replace the error-detected parts.
AWD control module
—
Voltage
Connector
Terminal
B47
3
Ground
0 V
AWD control module
—
Voltage
Connector
Terminal
B47
3
Ground
11 – 13 V
AWD control module
—
Continuity
Connector
Terminal
B47
10
Ground
Existed
11
DLN-68
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
P183C DECEL G SENSOR
P183C DECEL G SENSOR
DTC Logic
INFOID:0000000012199415
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION
With CONSULT
1. Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1 minute.
2. Stop the vehicle.
3. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P183C” detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012199416
1.
PERFORM ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “ABS”.
Is any DTC detected?
YES
>> Perform trouble diagnosis for detected DTC. Refer to
NO
>> GO TO 2.
2.
ERASE SELF-DIAGNOSTIC RESULT
With CONSULT
1. Erase self-diagnostic results for “ALL MODE AWD/4WD”.
2. Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1 minute.
3. Stop the vehicle.
4. Check that ABS warning lamp turns OFF.
Does ABS warning lamp turn OFF?
YES
>> GO TO 3.
NO
>> Refer to
BRC-136, "Component Function Check"
3.
CHECK TERMINALS AND HARNESS CONNECTORS
Check AWD control module pin terminals for damage or loose connection with harness connector.
Is inspection result normal?
YES
>> After turning the ignition switch OFF, perform DTC confirmation procedure again. If DTC “P183C”
is detected, Replace AWD control module. Refer to
DLN-91, "Removal and Installation"
NO
>> Repair or replace error-detected parts.
DTC
Display item
Malfunction detected condition
Possible cause
P183C
DECEL G SENSOR
Malfunction is detected in decel G sen-
sor signal that is output from ABS actua-
tor and electric unit (control unit) through
CAN communication.
• ABS actuator and electric unit (control
unit)
• Yaw rate/side/decel G sensor (Decel
G sensor signal)
• AWD control module
• CAN communication line
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст