Nissan Juke F15. Manual — part 264
P182E AWD SOLENOID (RIGHT)
DLN-61
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 2.
2.
CHECK AWD SOLENOID CIRCUIT (2)
1. Disconnect rear final drive sub-harness connector.
2. Check the continuity between AWD control module harness connector and rear final drive sub-harness
connector.
3. Check the continuity between AWD control module harness connector and the ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the error-detected parts.
3.
CHECK REAR FINAL DRIVE SUB-HARNESS
1. Disconnect electric controlled coupling (right) harness connector.
2. Check the continuity between rear final drive sub-harness connector and electric controlled coupling
(right) harness connector.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace rear final drive sub-harness. Refer to
4.
CHECK AWD SOLENOID
Check AWD solenoid. Refer to
DLN-62, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> AWD solenoid (right) is malfunctioning. Replace electric controlled coupling (right). Refer to
145, "Removal and Installation"
5.
CHECK TERMINALS AND HARNESS CONNECTORS
1. Check AWD control module pin terminals for damage or loose connection with harness connector.
2. Check rear final drive sub-harness pin terminals for damage or loose connection with harness connector.
AWD control module
Condition
Resistance (Approx.)
Connector
Terminal
B47
25
26
10
°C (50°F)
2.55
Ω
20
°C (68°F)
2.65
Ω
30
°C (86°F)
2.76
Ω
AWD control module
Rear final drive sub-harness
Continuity
Connector
Terminal
Connector
Terminal
B47
25
B64
2
Existed
26
6
AWD control module
—
Continuity
Connector
Terminal
B47
25
Ground
Not existed
26
Rear final drive sub-harness
Electric controlled coupling (right)
Continuity
Connector
Terminal
Connector
Terminal
B84
2
B86
2
Existed
6
6
DLN-62
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
P182E AWD SOLENOID (RIGHT)
3. Check electric controlled coupling (right) pin terminals for damage or loose connection with harness con-
nector.
Is the inspection result normal?
YES
>> Replace AWD control module. Refer to
DLN-91, "Removal and Installation"
.
NO
>> Repair or replace the error-detected parts.
Component Inspection
INFOID:0000000012199406
1.
CHECK AWD SOLENOID
1. Turn the ignition switch OFF.
2. Disconnect electric controlled coupling (right) harness connector.
3. Check the resistance between electric controlled coupling (right) connector terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> AWD solenoid (right) is malfunctioning. Replace electric controlled coupling (right). Refer to
145, "Removal and Installation"
.
Electric controlled coupling (right)
Condition
Resistance (Approx.)
Terminal
2
6
10
°C (50°F)
2.55
Ω
20
°C (68°F)
2.65
Ω
30
°C (86°F)
2.75
Ω
P1830 ABS OPERATION SIGNAL
DLN-63
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
P1830 ABS OPERATION SIGNAL
DTC Logic
INFOID:0000000012199407
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION
With CONSULT
1. Start the engine and drive at 30 km/h (19 MPH) or more for approximately 3 minute.
2. Stop the vehicle.
3. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P1830” detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012199408
1.
PERFORM ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “ABS”.
Is any DTC detected?
YES
>> Perform trouble diagnosis for detected DTC. Refer to
NO
>> GO TO 2.
2.
ERASE SELF-DIAGNOSTIC RESULT
With CONSULT
1. Erase self-diagnostic results for “ALL MODE AWD/4WD”.
2. Start the engine and drive at 30 km/h (19 MPH) or more for approximately 3 minute.
3. Stop the vehicle.
4. Check that ABS warning lamp turns OFF.
Does ABS warning lamp turn OFF?
YES
>> GO TO 3.
NO
>> Refer to
BRC-136, "Component Function Check"
.
3.
CHECK TERMINALS AND HARNESS CONNECTORS
Check AWD control module pin terminals for damage or loose connection with harness connector.
Is inspection result normal?
YES
>> After turning the ignition switch OFF, perform DTC confirmation procedure again. If DTC “P1830”
is detected, Replace AWD control module. Refer to
DLN-91, "Removal and Installation"
NO
>> Repair or replace error-detected parts.
DTC
Display item
Malfunction detected condition
Possible cause
P1830
ABS OP SIG
Malfunction is detected in ABS operation
signal that is output from ABS actuator
and electric unit (control unit) through
CAN communication.
• ABS actuator and electric unit (control
unit)
• AWD control module
• CAN communication line
DLN-64
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
P1831 VDC OPERATION SIGNAL
P1831 VDC OPERATION SIGNAL
DTC Logic
INFOID:0000000012199409
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION
With CONSULT
1. Start the engine and drive at 30 km/h (19 MPH) or more for approximately 3 minute.
2. Stop the vehicle.
3. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P1831” detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012199410
1.
PERFORM ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “ABS”.
Is any DTC detected?
YES
>> Perform trouble diagnosis for detected DTC. Refer to
NO
>> GO TO 2.
2.
ERASE SELF-DIAGNOSTIC RESULT
With CONSULT
1. Erase self-diagnostic results for “ALL MODE AWD/4WD”.
2. Start the engine and drive at 30 km/h (19 MPH) or more for approximately 3 minute.
3. Stop the vehicle.
4. Check that ABS warning lamp turns OFF.
Does ABS warning lamp turn OFF?
YES
>> GO TO 3.
NO
>> Refer to
BRC-136, "Component Function Check"
3.
CHECK TERMINALS AND HARNESS CONNECTORS
Check AWD control module pin terminals for damage or loose connection with harness connector.
Is inspection result normal?
YES
>> After turning the ignition switch OFF, perform DTC confirmation procedure again. If DTC “P1831”
is detected, Replace AWD control module. Refer to
DLN-91, "Removal and Installation"
NO
>> Repair or replace error-detected parts.
DTC
Display item
Malfunction detected condition
Possible cause
P1831
VDC OP SIG
Malfunction is detected in VDC opera-
tion signal that is output from ABS actu-
ator and electric unit (control unit)
through CAN communication.
• ABS actuator and electric unit (control
unit)
• AWD control module
• CAN communication line
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст