Nissan Juke F15. Manual — part 1335
TM-530
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
P2815 SELECT SOLENOID
P2815 SELECT SOLENOID
DTC Logic
INFOID:0000000012201224
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
1. Start the engine.
2. Maintain the following conditions. (Keep 5 seconds or more after the selector lever shifted.)
3. Check the first trip DTC.
Is “P2815” detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012201225
1.
CHECK CIRCUIT BETWEEN TCM AND CVT UNIT
1. Turn ignition switch OFF.
2. Disconnect TCM connector and CVT unit connector.
3. Check continuity between TCM harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace damaged parts.
2.
CHECK CIRCUIT BETWEEN CVT UNIT AND GROUND
Check continuity between CVT unit harness connector terminal and ground.
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
Possible causes
P2815
SELECT SOLENOID
(Select solenoid)
When all of the following conditions are satis-
fied and this state is maintained for 0.2 sec-
onds:
• TCM power supply voltage: More than 11 V
• TCM judges that solenoid valve circuit is
open.
• P2814 is not detected.
• Harness or connector
(Select solenoid valve circuit open or
shorted to power supply)
• Select solenoid valve
Selector lever
: N
→ D, N → R, P → R
TCM
CVT unit
Continuity
Connector
Terminal
Connector
Terminal
F83
37
F82
4
Existed
P2815 SELECT SOLENOID
TM-531
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
NO
>> There is malfunction of select solenoid valve. Replace transaxle assembly. Refer to
.
CVT unit
—
Condition
Resistance
Connector
Terminal
F250
4
Ground
CVT fluid temperature: 20
°C (68°F)
5.5 – 7.0
Ω
CVT fluid temperature: 50
°C (122°F)
6.0 – 8.0
Ω
CVT fluid temperature: 80
°C (176°F)
6.5 – 8.5
Ω
TM-532
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
MAIN POWER SUPPLY AND GROUND CIRCUIT
MAIN POWER SUPPLY AND GROUND CIRCUIT
Diagnosis Procedure
INFOID:0000000012201226
1.
CHECK TCM POWER CIRCUIT (PART 1)
1. Turn ignition switch OFF.
2. Disconnect TCM connector.
3. Check voltage between TCM harness connector terminals and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 4.
2.
CHECK TCM POWER CIRCUIT (PART 2)
Check voltage between TCM harness connector terminals and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 5.
3.
CHECK TCM GROUND CIRCUIT
Check continuity between TCM harness connector terminals and ground.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
NO
>> Repair or replace malfunctioning parts.
4.
DETECT MALFUNCTION ITEMS (PART 1)
Check the following items:
• Open circuit or short circuit in harness between battery positive terminal and TCM connector terminal 45,
and 46.
• 10A fuse (No.23, located in the fuse holder). Refer to
PG-81, "Fuse and Fusible Link Arrangement"
• 10A fuse (No.33, located in the fuse holder). Refer to
PG-81, "Fuse and Fusible Link Arrangement"
Is the inspection result normal?
YES >> Check
intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
NO
>> Repair or replace malfunctioning parts.
+
−
Voltage
TCM
Connector
Terminal
F83
45
Ground
10 – 16 V
46
+
−
Condition
Voltage
TCM
Connector
Terminal
F83
47
Ground
Ignition switch ON
10 – 16 V
Ignition switch OFF
Approx. 0 V
48
Ignition switch ON
10 – 16 V
Ignition switch OFF
Approx. 0 V
TCM
—
Continuity
Connector
Terminal
F83
41
Ground
Existed
42
MAIN POWER SUPPLY AND GROUND CIRCUIT
TM-533
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
5.
CHECK CIRCUIT BETWEEN IPDM E/R AND TCM
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector terminal and TCM harness connector terminals.
Is the check result normal?
YES
>> GO TO 6.
NO
>> Repair or replace malfunctioning parts.
6.
DETECT MALFUNCTIONING ITEMS (PART 2)
Check the following items:
• Open circuit or short circuit in harness between ignition switch and IPDM E/R. Refer to
gram - IGNITION POWER SUPPLY -"
.
• Short circuit in harness between IPDM E/R harness connector terminal 57 and TCM harness connector ter-
minals 47, and 48.
• 10A fuse (No.55, located in the IPDM E/R). Refer to
PG-80, "Fuse, Connector and Terminal Arrangement"
• IPDM E/R
Is the check result normal?
YES
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
NO
>> Repair or replace malfunctioning parts.
IPDM E/R
TCM
Continuity
Connector
Terminal
Connector
Terminal
E15
57
F83
47
Existed
48
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст