Nissan Juke F15. Manual — part 914
IP-20
< REMOVAL AND INSTALLATION >
INSTRUMENT PANEL ASSEMBLY
21. Remove cluster lid C.
1. Remove fixing screws (A).
2. Pull back cluster lid C, and disengage the pawls and metal
clips.
3. Disconnect harness connector.
22. Remove audio unit or NAVI C/U.
• Audio unit: Refer to
AV-50, "Removal and Installation"
• NAVI C/U: Refer to
AV-182, "Removal and Installation"
23. Disconnect hazard switch harness connector.
24. Remove cluster tray.
1. Insert a remover tool (A) between cluster tray and instru-
ment panel assembly, and then pull downward and disen-
gage metal clips.
2. Pull back cluster tray.
3. Disconnect harness connectors.
CAUTION:
Apply protective tape (B) on the part to protect it from dam-
age.
25. Release front pillar portion of front body side welt RH. Refer to
INT-21, "BODY SIDE WELT : Removal and
.
26. Remove front pillar garnish RH. Refer to
INT-18, "FRONT PILLAR GARNISH : Removal and Installation"
27. Remove instrument side finisher RH.
1. Insert remover tool (A) between instrument side finisher RH
and instrument panel assembly to disengage the pawls as
shown in the figure.
2. Pull back instrument side finisher RH.
CAUTION:
Apply protective tape (B) on the part to protect it from dam-
age.
28. Remove glove box lid.
1. Open glove box lid.
2. Pull glove box lid (1) toward vehicle rear, and then disen-
gage the joint from instrument panel assembly (2).
: Pawl
: Metal clip
JMJIA4559ZZ
: Metal clip
JMJIA4560ZZ
: Pawl
JMJIA4561ZZ
JMJIA4563ZZ
INSTRUMENT PANEL ASSEMBLY
IP-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
3. Disengage the pawl, and then remove damper pin on right
side.
CAUTION:
Never excessively pull string of glove box damper.
29. Remove glove box assembly.
1. Remove fixing screws (A).
2. Pull back the glove box cover assembly while holding the lower side and disengage the pawls.
3. Disconnect glove box lamp harness connector.
30. Remove passenger air bag module. Refer to
SR-18, "Removal and Installation"
.
31. Remove switch panel.
1. Insert remover tool (A) between switch panel and instru-
ment panel assembly to disengage the pawls as shown in
the figure.
2. Pull up switch panel, and then disconnect harness connec-
tors.
CAUTION:
Apply protective tape (B) on the part to protect it from dam-
age.
32. Remove instrument panel assembly.
: Pawl
JMJIA4564ZZ
: Pawl
JMJIA4565ZZ
: Pawl
JMJIA4566ZZ
IP-22
< REMOVAL AND INSTALLATION >
INSTRUMENT PANEL ASSEMBLY
1. Remove instrument panel assembly mounting screws (A) and bolts (B).
CAUTION:
Cover tool with a shop cloth to prevent windshield glass from being damaged.
2. Disengage harness (A) and harness (B) of front pillar LH and RH portions from instrument panel
assembly.
3. Remove instrument panel from passenger door opening portion.
CAUTION:
• Cover CVT shift selector upper surface with a shop cloth to prevent it from being damaged.
• When removing instrument panel assembly, 2 workers are required to prevent it from drop-
ping.
33. Remove the following parts after removing instrument panel assembly.
• Side defroster nozzle: Refer to
VTL-9, "SIDE DEFROSTER NOZZLE : Removal and Installation"
• Side defroster grille: Refer to
VTL-10, "SIDE DEFROSTER GRILLE : Removal and Installation"
.
• Side ventilator grille: Refer to
VTL-9, "SIDE VENTILATOR GRILLE : Removal and Installation"
.
• Front defroster nozzle: Refer to
VTL-10, "FRONT DEFROSTER NOZZLE : Removal and Installation"
.
• Center ventilator duct: Refer to
VTL-11, "CENTER VENTILATOR DUCT : Removal and Installation"
• Side ventilator duct: Refer to
VTL-11, "SIDE VENTILATOR DUCT : Removal and Installation"
.
• GPS antenna: Refer to
AV-188, "Removal and Installation"
• Hazard switch: Refer to
EXL-107, "Removal and Installation"
(XENON TYPE) or
(HALOGEN TYPE).
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
• After installation, adjust the parking brake lever stroke. Refer to
PB-4, "Inspection and Adjustment"
• Never use the steering wheel mounting nut after removal, replace with the new nut.
• Never use the driver air bag module mounting bolts after removal, replace with the new bolts.
• Never use the passenger air bag module mounting bolts after removal, replace with the new bolts.
JMJIA4567ZZ
JMJIA4568ZZ
CENTER CONSOLE ASSEMBLY
IP-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
CENTER CONSOLE ASSEMBLY
Exploded View
INFOID:0000000012199208
CVT models
JSJIA0055ZZ
1.
Console indicator finisher
2.
Instrument lower cover RH
3.
Center console assembly
4.
Instrument lower cover LH
5.
Instrument stay
6.
CVT shift selector assembly
7.
Console rear bracket
8.
Console rear finisher
9.
Seat heated switch (If equipped)
10. Console switch finisher
11. Console switch finisher
12. Console finisher assembly
13. Console mask
14. Console front bracket
: Pawl
: Metal clip
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст