Nissan Juke F15. Manual — part 915
IP-24
< REMOVAL AND INSTALLATION >
CENTER CONSOLE ASSEMBLY
MT models
Removal and Installation
INFOID:0000000012199209
WARNING:
Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes or
more.
REMOVAL
CAUTION:
When removing, always use a remover tool that is made of plastic.
JSJIA0056ZZ
1.
Console boot
2.
Instrument lower cover RH
3.
Center console assembly
4.
Instrument lower cover LH
5.
Instrument stay
6.
Console center bracket
7.
Console rear bracket
8.
Console rear finisher
9.
Seat heated switch (If equipped)
10. Console switch finisher
11. Console switch finisher
12. Console finisher assembly
13. Console mask
14. Console front bracket
: Pawl
: Metal clip
CENTER CONSOLE ASSEMBLY
IP-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
1. Remove shift lever knob (MT models only). Refer to
TM-25, "Removal and Installation"
(6MT: RS6F94R)
TM-83, "Removal and Installation"
(6MT: RS6F52H).
2. Remove console finisher assembly.
1. Put selector lever in “N” position.
2. Loosen the parking brake lever stroke by turning the adjusting nut with a socket wrench. Refer to
4, "Inspection and Adjustment"
.
3. Lift up console finisher assembly in numerical order shown in the figure and disengage metal clips.
4. Remove console finisher assembly while pulling it towards vehicle rear.
CAUTION:
• Be careful not for damaging parts in surrounding area.
• Remove metal clips slowly so that they are not damaged.
3. Remove console rear finisher.
1. Put front seat assembly (LH and RH) to frontmost position.
2. Pull back console rear finisher, and disengage the pawls
and metal clips.
: Metal clip
JSJIA0057ZZ
: Pawl
: Metal clip
JMJIA4183ZZ
IP-26
< REMOVAL AND INSTALLATION >
CENTER CONSOLE ASSEMBLY
4. Remove center console assembly fixing screws (A).
5. Remove instrument lower cover LH.
1. Put front seat assembly LH to rearmost position.
2. Remove fixing clip (A).
3. Pull the instrument lower cover LH crosswise, and disen-
gage the pawl and metal clips.
CAUTION:
Remove pawl and metal clips slowly so that they are not
damaged.
6. Remove instrument lower cover RH.
1. Put front seat assembly RH to rearmost position.
2. Remove fixing clip (A).
3. Pull the instrument lower cover RH crosswise, and disen-
gage the pawl and metal clips.
CAUTION:
Remove pawl and metal clips slowly so that they are not
damaged.
7. Remove center console assembly.
1. Remove center console fixing screws (A).
2. Lift up center console assembly back side.
CAUTION:
Be careful not for damaging parts in surrounding area.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
After installation, adjust the parking brake lever stroke. Refer to
PB-4, "Inspection and Adjustment"
JMJIA4202ZZ
: Pawl
: Metal clip
JMJIA4551ZZ
: Pawl
: Metal clip
JMJIA4552ZZ
JMJIA4553ZZ
CENTER CONSOLE ASSEMBLY
IP-27
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
Disassembly and Assembly
INFOID:0000000012199210
Disassembly and Assembly of Console Finisher Assembly
CAUTION:
When disassembling, always use a remover tool that is made of plastic.
DISASSEMBLY
1. Remove console finisher assembly. Refer to
IP-24, "Removal and Installation"
.
2. Remove console indicator finisher (CVT models)
Disengage connection of the console indicator finisher (2) fixing
pawls from the inside of the console finisher assembly (1)
toward the outside, and remove.
3. Remove console indicator finisher (MT models)
Disengage connection of the console boot (2) fixing pawls from
the inside of the console finisher assembly (1) toward the out-
side, and remove.
4. Remove console switch finisher.
Disengage connection of the console switch finisher (2) fixing
pawls from the inside of the console finisher assembly (1)
toward the outside, and remove.
NOTE:
Remove seat heated switch. Refer to
.
ASSEMBLY
Assemble in the reverse order of disassembly.
: Pawl
JMJIA4204ZZ
: Pawl
JMJIA4573ZZ
: Pawl
JMJIA4574ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст