Nissan Juke F15. Manual — part 1222
TM-78
< DTC/CIRCUIT DIAGNOSIS >
[6MT: RS6F52H]
POSITION SWITCH
DTC/CIRCUIT DIAGNOSIS
POSITION SWITCH
BACK-UP LAMP SWITCH
BACK-UP LAMP SWITCH : Component Inspection
INFOID:0000000012200805
1.
CHECK BACK-UP LAMP SWITCH
1. Disconnect position switch connector. Refer to
TM-82, "Removal and Installation"
.
2. Check continuity between position switch terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace position switch. Refer to
TM-82, "Removal and Installation"
.
PARK/NEUTRAL POSITION (PNP) SWITCH
PARK/NEUTRAL POSITION (PNP) SWITCH : Component Inspection
INFOID:0000000012200806
1.
CHECK PARK/NEUTRAL POSITION (PNP) SWITCH
1. Disconnect position switch connector. Refer to
TM-82, "Removal and Installation"
.
2. Check continuity between position switch terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace position switch.
Gear position
Continuity
Reverse
Yes
Except reverse
No
1
: Park/Neutral position (PNP) switch
2
: Back-up lamp switch
PCIB1970E
Gear position
Continuity
Neutral
Yes
Except neutral
No
PCIB1970E
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
TM-79
< SYMPTOM DIAGNOSIS >
[6MT: RS6F52H]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
SYMPTOM DIAGNOSIS
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000012200807
Use the chart below to help you find the cause of the symptom. The numbers indicate the order of the inspec-
tion. If necessary, repair or replace these parts.
SUSPECTED PARTS
(Possible cause)
OI
L
(O
il le
ve
l i
s l
o
w
.)
O
IL (W
ro
ng
oi
l.)
OI
L
(O
il le
ve
l i
s h
ig
h
.)
GASKET (Damaged)
OIL SEAL
(W
orn or
damaged)
SHIFT
CON
T
ROL LINKAGE (W
orn)
STRIKI
NG
ROD
ASSEMBL
Y (W
orn or damaged)
SHIFT
FORK (W
orn
)
G
EAR (W
orn
or
da
ma
ge
d)
BEARING (W
orn or damaged)
BAULK
RING
(W
orn
or
da
ma
ge
d)
INSER
T SPRI
N
G
(D
amaged)
Reference page
,
,
,
,
Symptoms
Noise
1
2
3
3
Oil leakage
3
1
2
2
Hard to shift or will not shift
1
1
2
3
3
Jumps out of gear
1
2
3
3
TM-80
< PERIODIC MAINTENANCE >
[6MT: RS6F52H]
GEAR OIL
PERIODIC MAINTENANCE
GEAR OIL
Inspection
INFOID:0000000012200808
OIL LEAKAGE
Make sure that gear oil is not leaking from transaxle or around it.
OIL LEVEL
1. Remove filler plug (1) and gasket from transaxle case.
2. Check the oil level from filler plug mounting hole as shown in the
figure.
CAUTION:
Never start engine while checking oil level.
3. Set a gasket on filler plug and then install it to transaxle case.
CAUTION:
Never reuse gasket.
4. Tighten filler plug to the specified torque. Refer to
Draining
INFOID:0000000012200809
1. Start engine and let it run to warm up transaxle.
2. Stop engine. Remove drain plug (1) and gasket, using a socket
[Commercial service tool] and then drain gear oil.
3. Set a gasket on drain plug and install it to clutch housing, using
a socket [Commercial service tool].
CAUTION:
Never reuse gasket.
4. Tighten drain plug to the specified torque. Refer to
Refilling
INFOID:0000000012200810
Refilling
1. Remove plug (1). Fill the transaxle with new oil and check the oil
level (L) using suitable gauge (A) as shown.
2. Install a new O-ring onto plug (1) and then install it to transaxle.
Tighten to the specified torque. Refer to
.
CAUTION:
Do not reuse O-ring.
PCIB1968E
PCIB1834E
Oil grade and capacity
: Refer to
Oil level (L)
: 38.5 - 45.5 mm (1.516 - 1.791 in)
PCIB1968E
SIDE OIL SEAL
TM-81
< REMOVAL AND INSTALLATION >
[6MT: RS6F52H]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
REMOVAL AND INSTALLATION
SIDE OIL SEAL
Removal and Installation
INFOID:0000000012200811
REMOVAL
1. Remove front drive shafts from transaxle assembly. Refer to
FAX-28, "2WD : Removal and Installation"
2. Remove differential side oil seal (1) using a suitable tool.
CAUTION:
Do not damage transaxle case and clutch housing.
INSTALLATION
Installation is in the reverse order of removal.
• Install differential side oil seal to clutch housing and transaxle case
to the specified dimension (A) using Tools.
CAUTION:
Do not reuse oil seal.
• Check oil level after installation. Refer to
SCIA7625E
Dimension A)
: -0.5 - 0.5 mm (-0.020 - 0.020 in)
Tool numbers
: ST30720000 (J-25405)
: ST33400001 (J-26082)
SCIA1010E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст