Nissan Juke F15. Manual — part 1223
TM-82
< REMOVAL AND INSTALLATION >
[6MT: RS6F52H]
POSITION SWITCH
POSITION SWITCH
Removal and Installation
INFOID:0000000012200812
REMOVAL
1. Remove battery. Refer to
PG-105, "Removal and Installation"
.
2. Disconnect position switch connector.
3. Remove position switch from transaxle case.
INSTALLATION
1. Apply recommended sealant to threads of position switch.
• Use Genuine Silicone RTV or an equivalent. Refer to
GI-22, "Recommended Chemical Products
CAUTION:
Remove old sealant and oil adhering to threads.
2. Install position switch to transaxle case.
3. Tighten position switch to the specified torque. Refer to
4. For the next step and after, install in the reverse order of removal.
Inspection
INFOID:0000000012200813
INSPECTION AFTER INSTALLATION
• Check continuity between position switch terminals. Refer to
TM-78, "BACK-UP LAMP SWITCH : Compo-
(Back-up lamp switch) and
TM-78, "PARK/NEUTRAL POSITION (PNP) SWITCH : Compo-
(PNP switch).
• Check the oil leakage. Refer to
CONTROL LINKAGE
TM-83
< REMOVAL AND INSTALLATION >
[6MT: RS6F52H]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
CONTROL LINKAGE
Exploded View
INFOID:0000000012200814
Removal and Installation
INFOID:0000000012200815
REMOVAL
1. Remove battery. Refer to
PG-105, "Removal and Installation"
.
2. Remove air cleaner and air duct. Refer to
EM-27, "Removal and Installation"
.
3. Remove shift cable from shifter lever as shown.
1.
Shift selector knob
2.
Shift selector
3.
Shift selector assembly
4.
Select cable
5.
Lock plate
6.
Cable bracket
7.
Shift cable
8.
Cable support bracket
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
LCIA0414E
BCIA0052E
TM-84
< REMOVAL AND INSTALLATION >
[6MT: RS6F52H]
CONTROL LINKAGE
4. Remove select cable from selector lever A as shown.
5. Move shift selector to neutral position.
6. Remove shift selector knob.
7. Remove center console assembly. Refer to
IP-24, "Removal and Installation"
8. Remove shift selector assembly nuts.
9. Remove exhaust front tube, center muffler and heat shield. Refer to
EX-10, "Removal and Installation"
10. Remove cable support bracket.
11. Remove select cable and shift cable from cable bracket.
12. Remove shift selector assembly from the vehicle.
INSTALLATION
Installation is in the reverse order of removal.
• Securely install each cable to shifter lever and selector lever.
• Be careful about the installation direction, and screw shift selector
knob onto shift selector.
: Front
• When shift selector is selected to 1st-2nd side and 5th-6th side, confirm shift selector returns to neutral posi-
tion smoothly.
• When shift selector is shifted to each position, make sure there is no binding or disconnection in each boot.
BCIA0057E
SCIA7630E
AIR BREATHER HOSE
TM-85
< REMOVAL AND INSTALLATION >
[6MT: RS6F52H]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
AIR BREATHER HOSE
Exploded View
INFOID:0000000012200816
Removal and Installation
INFOID:0000000012200817
REMOVAL
1. Disconnect clip of air breather hose from bracket.
2. Remove air breather hose from air breather tube of transaxle assembly.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Make sure there are no pinched or restricted areas on the air breather hose caused by bending or
winding when installing it.
• Never reuse clip.
• Be sure to insert air breather hose into air breather tube until hose end reaches the tube's base.
• Set air breather hose with painted mark facing forward.
• Install air breather hose to bracket by fully inserting the clip.
1.
Air breather hose
2.
Clip
3.
Transaxle assembly
4.
Air breather tube
5.
Bracket
6
Air cleaner case
: Always replace after every disassembly.
JSDIA7171ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст