Nissan Juke F15. Manual — part 1150
SEC-124
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
VEHICLE SECURITY SYSTEM CANNOT BE SET
NO
>> GO TO 1.
DOOR KEY CYLINDER
DOOR KEY CYLINDER : Description
INFOID:0000000012202232
ARMED phase is not activated when all doors are locked using mechanical key.
NOTE:
Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and check
each symptom.
CONDITION OF VEHICLE (OPERATING CONDITION)
• SECURITY ALARM SET: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using
CONSULT.
DOOR KEY CYLINDER : Diagnosis Procedure
INFOID:0000000012202233
1.
CHECK POWER DOOR LOCK SYSTEM
Lock or unlock doors using mechanical key.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check power door lock system. Refer to
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
NO
>> GO TO 1.
DOOR LOCK AND UNLOCK SWITCH
DOOR LOCK AND UNLOCK SWITCH : Description
INFOID:0000000012202234
Armed phase is not activated when all doors are locked by door lock and unlock switch.
NOTE:
Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDI-
TIONS)” before starting diagnosis, and check each symptom.
CONDITION OF VEHICLE (OPERATING CONDITIONS)
“SECURITY ALARM SET”: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using
CONSULT.
DOOR LOCK AND UNLOCK SWITCH : Diagnosis Procedure
INFOID:0000000012202235
1.
CHECK DOOR LOCK FUNCTION
Lock/unlock door using mechanical key inserted into door key cylinder.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check Intelligent Key system (remote keyless entry function). Refer to
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
NO
>> GO TO 1.
VEHICLE SECURITY ALARM DOES NOT ACTIVATE
SEC-125
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
VEHICLE SECURITY ALARM DOES NOT ACTIVATE
Description
INFOID:0000000012202236
Alarm does not operate when alarm operating condition is satisfied.
NOTE:
Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDI-
TIONS)” before starting diagnosis, and check each symptom.
CONDITION OF VEHICLE (OPERATING CONDITIONS)
“SECURITY ALARM SET”: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using
CONSULT.
Diagnosis Procedure
INFOID:0000000012202237
1.
CHECK DOOR SWITCH
Check door switch.
DLK-77, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace the malfunctioning door switch
2.
CHECK HEADLAMPS FUNCTION
Check head lamps function.
SEC-117, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
CHECK HORN FUNCTION
Check horn function.
SEC-118, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunctioning parts.
4.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
NO
>> GO TO 1.
SEC-126
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
NATS ANTENNA AMP.
REMOVAL AND INSTALLATION
NATS ANTENNA AMP.
Removal and Installation
INFOID:0000000012202238
REMOVAL
1. Remove the cluster lid A. Refer to
IP-13, "Removal and Installation"
.
2. Remove the NATS antenna amp.
1. Disengage the NATS antenna amp. (1) fixing pawls using
remover tool.
2. Pull NATS antenna amp. to remove it from push-button igni-
tion switch (2).
INSTALLATION
Install in the reverse order of removal.
: Pawl
JMKIA6573ZZ
PUSH-BUTTON IGNITION SWITCH
SEC-127
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
PUSH-BUTTON IGNITION SWITCH
Removal and Installation
INFOID:0000000012202239
REMOVAL
1. Remove the NATS antenna amp. Refer to
IP-13, "Removal and Installation"
2. Remove the push-button ignition switch.
1. Disengage the push-button ignition switch (1) fixing pawls
using remover tool.
2. Press the push-button ignition switch to remove it from clus-
ter lid A (2).
INSTALLATION
Install in the reverse order of removal.
: Pawl
JMKIA6574ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст