Nissan Juke F15. Manual — part 1149
SEC-120
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
SECURITY INDICATOR LAMP
1. Replace BCM. Refer to
BCS-94, "Removal and Installation"
.
2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.
>> INSPECTION END
5.
CHECK SECURITY INDICATOR LAMP CIRCUIT
1. Disconnect combination meter connector.
2. Check continuity between combination meter harness connector and BCM harness connector.
3. Check continuity between combination meter harness connector and ground.
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-64, "Removal and Installation"
NO
>> Repair or replace harness.
Combination meter
BCM
Continuity
Connector
Terminal
Connector
Terminal
M34
18
M68
23
Existed
Combination meter
Ground
Continuity
Connector
Terminal
M34
18
Not existed
ENGINE DOES NOT START WHEN INTELLIGENT KEY IS INSIDE OF VEHICLE
SEC-121
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
SYMPTOM DIAGNOSIS
ENGINE DOES NOT START WHEN INTELLIGENT KEY IS INSIDE OF VE-
HICLE
Description
INFOID:0000000012202224
Engine does not start when push-button ignition switch is pressed while carrying Intelligent Key.
NOTE:
• Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and
check each symptom.
• The engine start function, door lock function, power distribution system, and NATS-IVIS/NVIS in the Intelli-
gent Key system are closely related to each other regarding control. The vehicle security function can oper-
ate only when the door lock and power distribution systems are operating normally.
Conditions of Vehicle (Operating Conditions)
• “ENGINE START BY I-KEY”: ON
Check the setting of “ENGINE START BY I-KEY” in “Work Support” mode of “INTELLIGENT KEY” of “BCM”
using CONSULT.
• One or more of Intelligent Keys with registered Intelligent Key ID are in the vehicle.
Diagnosis Procedure
INFOID:0000000012202225
1.
PERFORM WORK SUPPORT
Perform “INSIDE ANT DIAGNOSIS” in “Work Support” mode of “INTELLIGENT KEY” of BCM using CON-
SULT.
DLK-28, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS RESULT
Perform Self-Diagnosis Result in “BCM”, and check whether or not DTC of inside key antenna is detected.
Is DTC detected?
YES
>> Refer to
NO
>> GO TO 3.
3.
CHECK PUSH-BUTTON IGNITION SWITCH
Check push-button ignition switch.
PCS-78, "Component Function Check"
Is the operation normal?
YES
>> GO TO 4.
NO
>> Repair or replace malfunctioning parts.
4.
CONFIRM THE OPERATION
Confirm the operation again.
Is the inspection normal?
YES
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
NO
>> GO TO 1.
SEC-122
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
SECURITY INDICATOR LAMP DOES NOT TURN ON OR BLINK
SECURITY INDICATOR LAMP DOES NOT TURN ON OR BLINK
Description
INFOID:0000000012202226
Security indicator lamp does not blink when ignition switch is in a position other than ON.
NOTE:
• Before performing the diagnosis, check “Work Flow”. Refer to
• Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDI-
TIONS)” before starting diagnosis, and check each symptom.
CONDITIONS OF VEHICLE (OPERATING CONDITIONS)
Power supply position is not the ON position.
Diagnosis Procedure
INFOID:0000000012202227
1.
CHECK SECURITY INDICATOR LAMP
Check security indicator lamp.
SEC-119, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
NO
>> GO TO 1.
VEHICLE SECURITY SYSTEM CANNOT BE SET
SEC-123
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
VEHICLE SECURITY SYSTEM CANNOT BE SET
INTELLIGENT KEY
INTELLIGENT KEY : Description
INFOID:0000000012202228
Armed phase is not activated when all doors are locked using Intelligent Key.
NOTE:
Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDI-
TIONS)” before starting diagnosis, and check each symptom.
CONDITION OF VEHICLE (OPERATING CONDITIONS)
“SECURITY ALARM SET”: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using
CONSULT.
INTELLIGENT KEY : Diagnosis Procedure
INFOID:0000000012202229
1.
CHECK INTELLIGENT KEY SYSTEM (REMOTE KEYLESS ENTRY FUNCTION)
Lock/unlock door with Intelligent Key.
DLK-18, "REMOTE KEYLESS ENTRY FUNCTION : System Description"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check Intelligent Key system (remote keyless entry function). Refer to
.
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
NO
>> GO TO 1.
DOOR REQUEST SWITCH
DOOR REQUEST SWITCH : Description
INFOID:0000000012202230
Armed phase is not activated when all doors are locked using door request switch.
NOTE:
Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDI-
TIONS)” before starting diagnosis, and check each symptom.
CONDITION OF VEHICLE (OPERATING CONDITIONS)
“SECURITY ALARM SET”: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using
CONSULT.
DOOR REQUEST SWITCH : Diagnosis Procedure
INFOID:0000000012202231
1.
CHECK INTELLIGENT KEY SYSTEM (DOOR LOCK FUNCTION)
Lock/unlock door with door request switch.
DLK-14, "DOOR LOCK FUNCTION : System Description"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check Intelligent Key system (door lock function). Refer to
SWITCHES : Diagnosis Procedure"
.
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст