Nissan Juke F15. Manual — part 903
INT-16
< REMOVAL AND INSTALLATION >
REAR DOOR FINISHER
REAR DOOR FINISHER
Exploded View
INFOID:0000000012199170
Removal and Installation
INFOID:0000000012199171
REMOVAL
CAUTION:
• When removing, always use a remover tool that is made of plastic.
• Never damage the door panel.
1. Fully open door window.
2. Remove rear corner cover inner.
1.
Rear door panel
2.
Grommet
3.
Rear door corner cover inner
4.
Cap
5.
Power window switch finisher
6.
Rear door finisher
: Clip
: Pawl
: Metal clip
JMJIA4522ZZ
REAR DOOR FINISHER
INT-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
Disengage rear corner cover inner fixing pawl with a remover
tool (A).
3. Remove power window switch finisher and power window switch in one body.
Pull up power window switch finisher and power window switch
with one body and disconnect harness connector.
4. Remove rear door finisher fixing screw.
5. Disengage rear door finisher fixing clips and metal clips with a
remover tool (A), and then remove rear door finisher.
CAUTION:
Insert a remover tool between body side panel and clip and
disengage pawl.
NOTE:
Remove power window switch. Refer to
PWC-54, "Removal and Installation"
.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
When installing rear door finisher, check that clips, and metal clips are securely in body panel holes,
and press them in.
: Clip
JMJIA4523ZZ
: Pawl
JMJIA4525ZZ
: Clip
: Metal clip
JMJIA4526ZZ
INT-18
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
BODY SIDE TRIM
Exploded View
INFOID:0000000012199172
FRONT PILLAR GARNISH
FRONT PILLAR GARNISH : Removal and Installation
INFOID:0000000012199173
REMOVAL
CAUTION:
1.
Rear body side welt
2.
Center pillar upper garnish
3.
Front body side welt
4.
Front pillar garnish
5.
Metal clip
6.
Dash side finisher RH
7.
Harness clip
8.
Front kicking plate inner
9.
Center pillar lower garnish
10. Rear kicking plate inner
: Clip
: Pawl
: Metal clip
: Vehicle front
: Always replace after every disassembly.
JMJIA4527ZZ
BODY SIDE TRIM
INT-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
• When removing, always use a remover tool that is made of plastic.
• Never damage the body.
1. Release front pillar garnish portion of front body side welt.
2. Remove front pillar garnish.
1. Disengage front pillar garnish fixing anchor clips with a
remover tool (A).
2. Cut anchor clip portion, and then remove front pillar garnish.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Replace anchor clip with a new part after removal. Never reuse anchor clip.
• Be sure to install anchor clip to front pillar garnish before installing front pillar garnish to the vehicle
body.
• When installing anchor clip to front pillar garnish, be sure to
align the notch and then insert anchor clip.
• After installing anchor clip to front pillar garnish, check that anchor clip is engaged securely to front
pillar garnish. If anchor clip is not engaged securely, front pillar garnish may be lifted and disen-
gaged from the vehicle body.
• When installing front pillar garnish, check that anchor clips are securely in body panel holes, and
press them in.
KICKING PLATE INNER
KICKING PLATE INNER : Removal and Installation
INFOID:0000000012199174
REMOVAL
CAUTION:
• When removing, always use a remover tool that is made of plastic to prevent damage to the parts.
• Never damage the body.
: Anchor Clip
JMJIA7046ZZ
JMJIA5130ZZ
JMJIA7045ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст