Nissan Juke F15. Manual — part 904
INT-20
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
FRONT KICKING PLATE INNER
1. Disengage fixing pawls on front lower end of front kicking plate
inner using a remover tool (A).
CAUTION:
Apply protective tape (B) on the parts to protect it from
damage.
2. Lift up toward vehicle upper and disengage fixing pawls of front
kicking plate inner starting from the front.
CAUTION:
Never lift up excessively. Otherwise, rear end of front kick-
ing plate inner may be damaged.
3. Lift up lower rear end of front kicking plate inner while pulling it
toward vehicle inside, disengage fixing pawls of front kicking
plate inner, and then remove front kicking plate inner.
REAR KICKING PLATE INNER
1. Remove rear seat cushion. Refer to
SE-32, "SEAT CUSHION : Removal and Installation"
.
2. Disengage fixing pawls on front lower end of rear kicking plate
inner using a remover tool (A).
CAUTION:
Apply protective tape (B) on the parts to protect it from
damage.
: Pawl
: Vehicle front
JMJIA6562ZZ
: Pawl
JMJIA6563ZZ
: Pawl
JMJIA6564ZZ
: Pawl
JMJIA6565ZZ
BODY SIDE TRIM
INT-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
3. Lift up toward vehicle upper and disengage fixing pawls of rear
kicking plate inner starting from the front.
CAUTION:
Never lift up excessively. Otherwise, rear end of rear kicking
plate inner may be damaged.
4. Using a remover tool (A), lift up lower rear end of rear kicking
plate inner while disengaging a fixing pawl on lower rear end of
rear kicking plate inner, disengage remaining fixing pawls, and
then remove rear kicking plate inner.
CAUTION:
Apply protective tape (B) on the parts to protect it from
damage.
INSATALLATION
Install in the reverse order of removal.
DASH SIDE FINISHER
DASH SIDE FINISHER : Removal and Installation
INFOID:0000000012199175
REMOVAL
CAUTION:
Never damage the body.
1. Remove front kicking plate inner. Refer to
INT-19, "KICKING PLATE INNER : Removal and Installation"
2. Pull back dash side finisher, and then disengage the pawls.
3. Disconnect dash side finisher, vehicle front side, from stud bolt and remove dash side finisher.
INSTALLATION
Install in the reverse order of removal.
BODY SIDE WELT
BODY SIDE WELT : Removal and Installation
INFOID:0000000012199176
REMOVAL
CAUTION:
• Never excessively pull body side welt.
• Never damage the body.
FRONT BODY SIDE WELT
: Pawl
JMJIA6566ZZ
: Pawl
JMJIA6567ZZ
: Pawl
JMJIA4529ZZ
INT-22
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
1. Remove front kicking plate inner. Refer to
INT-19, "KICKING PLATE INNER : Removal and Installation"
2. Remove front body side welt.
REAR BODY SIDE WELT
1. Remove rear kicking plate inner. Refer to
INT-19, "KICKING PLATE INNER : Removal and Installation"
.
2. Remove rear body side welt.
INSTALLATION
Install in the reverse order of removal.
CENTER PILLAR LOWER GARNISH
CENTER PILLAR LOWER GARNISH : Removal and Installation
INFOID:0000000012199177
REMOVAL
CAUTION:
• When removing, always use a remover tool that is made of plastic.
• Never damage the body.
1. Fully open front door and rear door.
2. Slide front seat to the fully forward position. Tilt seatback forward.
3. Remove Front body side welt and rear body side welt. Refer to
INT-21, "BODY SIDE WELT : Removal
4. Disengage center pillar lower garnish fixing clips and pawls with
a remover tool (A), and then remove center pillar lower garnish.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
When installing center pillar lower garnish, check that clips are securely in body panel holes, and
press them in.
CENTER PILLAR UPPER GARNISH
CENTER PILLAR UPPER GARNISH : Removal and Installation
INFOID:0000000012199178
REMOVAL
CAUTION:
• When removing, always use a remover tool that is made of plastic.
• Never damage the body.
1. Remove center pillar lower garnish. Refer to
INT-22, "CENTER PILLAR LOWER GARNISH : Removal
2. Remove front seat belt shoulder anchor. Refer to
SB-6, "SEAT BELT RETRACTOR : Removal and Instal-
.
: Clip
: Pawl
JMJIA4390ZZ
BODY SIDE TRIM
INT-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
3. Disengage center pillar upper garnish lower side fixing pawl
using a remover tool.
4. Disengage center pillar upper garnish upper side fixing clip using a remover tool (A).
NOTE:
Removal operation can be performed easily when pressing pawl by inserting a removal tool from direction
(A) as shown in the figure.
CAUTION:
Be careful not to apply excessive force when removing center pillar upper garnish. Otherwise,
pawl may be damaged and fragments may drop in panel holes on body.
INATALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Replace center pillar upper garnish with a new part after removal. Never reuse center pillar upper
garnish.
• When installing center pillar upper garnish, check that pawls are securely in body panel holes, and
press them in.
: Pawl
JMJIA4391ZZ
PIIB7674J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст